SFI SYSTEM, Diagnostic DTC:P060E49, P061E49

DTC Code DTC Name
P060E49 Internal Control Module Throttle Position Performance Internal Electronic Failure
P061E49 Internal Control Module Brake Signal Internal Electronic Failure

MONITOR DESCRIPTION

The ECM monitors the signals received from the No. 1 throttle position sensor and stop light switch assembly. As the ECM monitors the STP signal of the stop light switch assembly and the VTA1 signal of the No. 1 throttle position sensor, if these signals do not correlate, a DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P060E49 Internal Control Module Throttle Position Performance Internal Electronic Failure

Either of the following conditions is met (1 trip detection logic):


  • ECM main CPU malfunction.

  • ECM sub CPU malfunction.

 ECM Comes on DTC stored SAE Code: P060E
P061E49 Internal Control Module Brake Signal Internal Electronic Failure

Either of the following conditions is met (1 trip detection logic):


  • ECM main CPU malfunction.

  • ECM sub CPU malfunction.

 ECM Comes on DTC stored SAE Code: P061E

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the GTS off.

  5. Turn the engine switch off.

  6. Disconnect the GTS.

  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  8. Connect the cable to the negative (-) battery terminal.

  9. Connect the GTS to the DLC3.

  10. Turn the engine switch on (IG) and turn the GTS on.

  11. Wait for 16 seconds or more.

  12. Enter the following menus: Powertrain / Engine / Trouble Codes.

  13. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  15. Input the DTC: P060E49 or P061E49.

  16. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

CAUTION / NOTICE / HINT

Note

After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ OUTPUT DTC (DTC P060E49 OR P061E49)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the GTS off.

    6. Turn the engine switch off.

    7. Disconnect the GTS.

    8. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

    9. Connect the cable to the negative (-) battery terminal.

    10. Connect the GTS to the DLC3.

    11. Turn the engine switch on (IG).

    12. Turn the GTS on.

    13. Wait for 16 seconds or more.

    14. Enter the following menus: Powertrain / Engine / Trouble Codes.

    15. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P060E49 or P061E49 is output B

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

    REPLACE ECM Click here