REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear differential carrier assembly with differential support removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment

  1. Clear zero point calibration data and system information.

  2. Perform yaw rate and acceleration sensor zero point calibration and store system information.

  • VSC disabled or malfunctions

  • DTCs are stored

  • Slip indicator light illuminates

  • ABS warning light illuminates

  • Theft deterrent system (tilt sensor)*1

Click here

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (w/ Parallel Parking Assist Function)

for Initialization: Click here

for Calibration: Click here

Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (w/o Parallel Parking Assist Function)

for Initialization: Click here

for Calibration: Click here


  • Parking assist ECU initialization

  • Adjust steering angle

 Panoramic view monitor system

for Initialization: Click here

for Calibration: Click here

Initialize headlight ECU sub-assembly LH

  • Adaptive high beam system

  • Automatic headlight beam level control system

Click here


  • Ultrasonic sensor detection angle

  • Ultrasonic sensor detection angle registration

  • Intelligent clearance sonar system

  • LEXUS parking assist-sensor system (w/ Intelligent Clearance Sonar System)

Click here

Gas leaks from exhaust system Inspection after repair

  • Poor idle, etc.

  • Engine start function, etc.

for 8AR-FTS: Click here

for 2GR-FKS (w/ Canister Pump Module): Click here

for 2GR-FKS (w/o Canister Pump Module): Click here

*1: w/ TFT Meter Type

CAUTION:

The rear differential carrier assembly with differential support is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.

B005PO3C23
*a Object Exceeding Weight Limit of Engine Lifter

PROCEDURE


  1. DRAIN DIFFERENTIAL OIL


    1. B005OPG

      Using a 10 mm hexagon wrench, remove the differential inspection plug and gasket.

    2. B005NHM

      Using a 10 mm hexagon wrench, remove the rear differential drain plug and gasket to drain the differential oil.

  2. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

    Click here

  3. REMOVE REAR DRIVE SHAFT ASSEMBLY


    1. Remove the rear drive shaft assembly LH and RH.

      Click here

  4. REMOVE REAR STABILIZER BAR

    Click here

  5. LOOSEN NO. 2 REAR DIFFERENTIAL SUPPORT

    Tech Tips

    Loosen the bolts only when removal of the No. 2 rear differential support is required.


    1. B005L6F

      Loosen the 2 bolts.

  6. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT

    Note


    • Do not damage the contact surface when removing the rear differential carrier assembly with differential support.

    • The remaining oil may leak out when removing the rear differential carrier assembly with differential support.

    • Securely support the rear differential carrier assembly with differential support while performing this step to avoid excessively tilting or dropping the rear differential carrier assembly with differential support.

    • Remove the bolts and nuts with the rear differential carrier assembly with differential support secured.


    1. B005OOZ

      Disconnect the vacuum hose from the electro magnetic control coupling sub-assembly.

    2. B005LXSC02
      *A 8AR-FTS
      *1 Lower Rear Differential Mount Stopper
      *a Attachment
      *b Engine Lifter

      Support the rear differential carrier assembly with differential support with an engine lifter using 3 attachments or equivalent tools as shown in the illustration.

    3. for 8AR-FTS:


      1. Remove the 2 bolts (A) and rear differential dynamic damper from the differential support.

    4. for 2GR-FKS:


      1. Remove the 2 bolts (B).

    5. Remove the 2 bolts (C), 2 nuts and 2 lower rear differential mount stoppers from the No. 2 rear differential support.

      Tech Tips

      The nuts have tabs to prevent them from rotating.

    6. B005O8NC02
      *1 Vacuum Hose
      *a Clamp (A)
      *b Clamp (B)

      Disconnect the connector and disengage the clamp (A).

    7. Separate the vacuum hose from the clamp (B).

    8. B005LETC02
      *1 Vacuum Hose

      Slightly lower the rear differential carrier assembly with differential support, remove the vacuum hose from the clamp.

      Note

      Do not damage the vacuum hose and electro magnetic control coupling wire harness.

      Tech Tips

      Lower the engine lifter to the extent that the vacuum hose can still be removed.

    9. Lower the rear differential carrier assembly with differential support slowly to remove the rear differential carrier assembly with differential support.

      Note


      • Do not damage the vacuum hose and electro magnetic control coupling wire harness.

      • Move the engine lifter forward and backward as necessary to prevent the rear differential carrier assembly with differential support from contacting the rear suspension member sub-assembly.

  7. REMOVE DIFFERENTIAL SUPPORT


    1. B005Q9Q

      Remove the 3 bolts and differential support from the rear differential carrier assembly.

  8. REMOVE UPPER REAR DIFFERENTIAL MOUNT STOPPER


    1. B005OEK

      Remove the 2 upper rear differential mount stoppers from the No. 2 rear differential support.

  9. REMOVE NO. 2 REAR DIFFERENTIAL SUPPORT


    1. B005ORT

      Remove the 2 bolts, 2 nuts and No. 2 rear differential support.

      Tech Tips

      The nuts have tabs to prevent them from rotating.