KNEE AIRBAG ASSEMBLY(for Driver Side) INSTALLATION

PROCEDURE


  1. INSTALL TIRE PRESSURE WARNING RESET SWITCH (for LHD)

    Click here

  2. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. B001NX2E04
      Text in Illustration
      *a Airbag Connector
      *b Airbag Connector Lock

      Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the airbag connector lock to install the airbag connector.

    5. Engage the 2 claws to connect the DLC3.

    6. Connect the connector and engage the clamp to install the wire harness.

    7. Engage the 2 hooks to temporarily install the lower No. 1 instrument panel airbag assembly.

    8. Install the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  3. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. B001NWUE02
      Text in Illustration
      *1 No. 1 Interior Illumination Light Assembly
      *a Airbag Connector
      *b Airbag Connector Lock
      *c DLC3

      Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the airbag connector lock to install the airbag connector.

    5. Engage the 2 claws to connect the DLC3.

    6. Engage the 2 claws to connect the No. 1 interior illumination light assembly.

    7. Engage the 2 hooks to temporarily install the lower No. 1 instrument panel airbag assembly.

    8. Install the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  4. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    Click here

  5. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    Click here

  6. INSTALL INSTRUMENT SIDE PANEL

    for LHD Driver Side: Click here

    for RHD Driver Side: Click here

  7. INSTALL FRONT DOOR OPENING TRIM COVER

    for LHD Driver Side: Click here

    for RHD Driver Side: Click here

  8. INSTALL COWL SIDE TRIM BOARD

    for LHD Driver Side: Click here

    for RHD Driver Side: Click here

  9. INSTALL FRONT DOOR SCUFF PLATE

    for LHD Driver Side: Click here

    for RHD Driver Side: Click here

  10. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL

    Click here

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  13. INSPECT SRS WARNING LIGHT

    Click here

  14. INSPECT TIRE PRESSURE WARNING SYSTEM

    Click here

  15. PERFORM INITIALIZATION

    Click here