SPIRAL CABLE INSTALLATION

PROCEDURE


  1. INSPECT SPIRAL CABLE SUB-ASSEMBLY

    Note

    If the steering sensor is installed to a misaligned spiral cable sub-assembly, DTCs for an abnormal steering sensor value, such as DTC B1801, C1231 and C1433, will be stored and it will be impossible to correct the problem. If this happens, replace the spiral cable with sensor sub-assembly with a new one.


    1. Check if the spiral cable sub-assembly is centered.

      B001O3UE03
      Text in Illustration
      *A w/o Heated Steering Wheel System and Pre-crash Safety System *B w/ Heated Steering Wheel System or Pre-crash Safety System
      *a Flat Cable - -

      Tech Tips

      When the spiral cable sub-assembly is centered, the part (A) is positioned at the top and the part of the flat cable shown in the illustration can be seen.

    2. If the spiral cable sub-assembly is not centered, center it.


      1. B001O3PE01
        Text in Illustration
        *a Interlock

        While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

        Note


        • When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

        • Do not turn the spiral cable sub-assembly using the airbag wire harness.

        • If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly or spiral cable with sensor sub-assembly with a new one.

      2. While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to the position where the part of the flat cable shown in the illustration can be seen.

        B001NRDE03
        Text in Illustration
        *A w/o Heated Steering Wheel System and Pre-crash Safety System *B w/ Heated Steering Wheel System or Pre-crash Safety System
        *a Flat Cable *b Interlock

        Tech Tips

        The spiral cable sub-assembly can be rotated approximately 2.5 turns to both the left and right from the center.

  2. INSTALL SPIRAL CABLE SUB-ASSEMBLY


    1. B001NZXE05
      Text in Illustration
      *a Guide
      *b Pin
      *c Lock Pin

      Align the 2 pins and 2 guides, and engage the 6 claws to install the spiral cable sub-assembly to the steering sensor.

      Note


      • Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.

      • Do not damage the pins of the spiral cable sub-assembly and guides of the steering sensor.

      • The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the spiral cable sub-assembly to the steering sensor.

    2. Remove the lock pin from the steering sensor.

  3. INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).

    • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the front wheels are aligned facing straight ahead.

    4. Set the turn signal switch to the neutral position.

      Note

      If it is not in the neutral position, the turn signal switch pin may snap.

    5. Engage the 3 claws to install the spiral cable with sensor sub-assembly.

    6. Connect each connector.

  4. INSTALL UPPER STEERING COLUMN COVER

    Click here

  5. INSTALL LOWER STEERING COLUMN COVER

    for Manual Tilt and Manual Telescopic Steering Column: Click here

    for Power Tilt and Power Telescopic Steering Column: Click here

  6. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  7. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. B001ON7C03
      *A w/o Heated Steering Wheel System and Pre-crash Safety System
      *B w/ Heated Steering Wheel System or Pre-crash Safety System
      *a Flat Cable

      Check if the spiral cable with sensor sub-assembly is centered.

      Tech Tips

      When the spiral cable with sensor sub-assembly is centered, the part (A) is positioned at the top and the part of the flat cable shown in the illustration is visible.

    4. If the spiral cable with sensor sub-assembly is not centered, center it.


      1. B001NQLC01
        *A w/o Heated Steering Wheel System and Pre-crash Safety System
        *B w/ Heated Steering Wheel System or Pre-crash Safety System
        *a Interlock

        While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

        Note


        • When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

        • Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

      2. B001OHYC01
        *A w/o Heated Steering Wheel System and Pre-crash Safety System
        *B w/ Heated Steering Wheel System or Pre-crash Safety System
        *a Interlock
        *b Flat Cable

        While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to the position where the part of the flat cable is visible.

        Tech Tips

        The spiral cable with sensor sub-assembly can be rotate approximately 2.5 turns to both the left and right from the center.

  8. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  9. INSPECT STEERING WHEEL CENTER POINT

  10. INSTALL HORN BUTTON ASSEMBLY

    Click here

  11. INSTALL LOWER NO. 3 STEERING WHEEL COVER

    Click here

  12. INSTALL LOWER NO. 2 STEERING WHEEL COVER

    Click here

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column)

    Click here

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Tilt and Manual Telescopic Steering Column)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSPECT HORN BUTTON ASSEMBLY

    Click here

  16. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  17. INSPECT SRS WARNING LIGHT

    Click here

  18. ADJUST PARKING ASSIST MONITOR SYSTEM (w/ Parking Assist Monitor System)

    w/o Parallel Parking Assist Function: Click here

    w/ Parallel Parking Assist Function: Click here