BLOCKING SYSTEM, Diagnostic DTC:B1587

DTC Code DTC Name
B1587 Lost Communication for Immobiliser Communication Circuit

DESCRIPTION

When one of the following occurs: 1) the telephone transceiver assembly detects errors in its own communications with the ID code box (immobiliser code ECU); 2) the telephone transceiver assembly detects errors in the communication lines; 3) the ECU communication ID between the ID code box (immobiliser code ECU) and telephone transceiver assembly is different and an engine start is attempt, the telephone transceiver assembly stores DTC B1587.

DTC Code DTC Detection Condition Trouble Area
B1587

Either condition is met:


  • Error in communication between telephone transceiver assembly and ID code box (immobiliser code ECU)

  • Error in communication lines

  • Communication ID is different during communication with ID code box (immobiliser code ECU)

  • Telephone transceiver assembly

  • ID code box (immobiliser code ECU)

  • Wire harness or connector

WIRING DIAGRAM

A01W2G4E04

CAUTION / NOTICE / HINT

Note


  • Before troubleshooting for these DTCs, make sure no immobiliser system DTCs are present. If present, troubleshoot the immobiliser system DTCs first.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • When replacing the telephone transceiver assembly or ID code box (immobiliser code ECU), refer to the Service Bulletin.

  • When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.

PROCEDURE


  1. CHECK DTC OUTPUT


    1. Clear the DTCs Click here.

    2. Turn the engine switch off.

    3. Start the engine.

    4. Check for DTCs.

      OK
      DTC B1587 is not output.

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. REREGISTER ECU COMMUNICATION ID


    1. Reregister the ECU communication ID.

      Tech Tips

      Refer to the Service Bulletin.


    NEXT

  3. CHECK DTC OUTPUT


    1. Clear the DTCs Click here.

    2. Turn the engine switch off.

    3. Start the engine.

    4. Check for DTCs.

      OK
      DTC B1587 is not output.

    OK

    END

    NG

  4. CHECK CONNECTION OF CONNECTOR


    1. Turn the engine switch off.

    2. Check that the connectors are properly connected to the telephone transceiver assembly and ID code box (immobiliser code ECU).

      OK
      Connectors are properly connected.

    NG

    CONNECT CONNECTOR CORRECTLY

    OK

  5. CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - ID CODE BOX (IMMOBILISER CODE ECU))


    1. Disconnect the H15 ID code box (immobiliser code ECU) connector.

    2. Disconnect the H102 telephone transceiver assembly connector.

    3. Measure the resistance and voltage according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H102-1 (BLK1) - H15-3 (EFII) Always Below 1 Ω
      H102-1 (BLK1) - Body ground Always 10 kΩ or higher
      H102-2 (BLK4) - H15-4 (EFIO) Always Below 1 Ω
      H102-2 (BLK4) - Body ground Always 10 kΩ or higher
      Standard Voltage
      Tester Connection Condition Specified Condition
      H102-1 (BLK1) - Body ground Always Below 1 V
      H102-2 (BLK4) - Body ground Always Below 1 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. REPLACE ID CODE BOX (IMMOBILISER CODE ECU)


    1. Temporarily replace the ID code box (immobiliser code ECU) with a new one.

      Tech Tips

      Refer to the Service Bulletin.


    NEXT

  7. REGISTER ECU COMMUNICATION ID


    1. Register the ECU communication ID.

      Tech Tips

      Refer to the Service Bulletin.


    NEXT

  8. CHECK DTC OUTPUT


    1. Clear the DTCs Click here.

    2. Turn the engine switch off.

    3. Start the engine.

    4. Check for DTCs.

      OK
      DTC B1587 is not output.

    OK

    END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

    NG

    REPLACE TELEPHONE TRANSCEIVER ASSEMBLY