INSTRUMENT PANEL SAFETY PAD INSTALLATION

PROCEDURE


  1. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY


    1. Engage the 4 guides and temporarily install the instrument panel safety pad assembly as shown in the illustration.

      B001OMA

      Note


      • Do not damage the instrument panel safety pad assembly.

      • Do not allow the wire harnesses to interfere with the surrounding parts.

    2. Install the 3 clips.

    3. Install the 5 bolts <C> and nut <F>.

    4. Install the 2 bolts <A>.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    5. Engage the 2 claws to connect the cooler (room temp. sensor) thermistor.

    6. Engage the claw and each clamp.

    7. Connect each connector.

  2. CONNECT NO. 2 INSTRUMENT PANEL WIRE

    Click here

  3. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Engage the 8 claws to install the instrument panel finish panel sub-assembly.

  4. INSTALL NO. 1 ION GENERATOR SUB-ASSEMBLY (w/ Ion Generator)

    Click here

  5. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY

    Click here

  6. INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY


    1. B001NS2

      Engage the 2 claws and 4 clips to install the No. 1 speaker opening cover assembly as shown in the illustration.

  7. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

    Click here

  8. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B001NN9

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clips to install the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.

  9. INSTALL FRONT PILLAR GARNISH LH

    Click here

  10. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  11. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B001NQO

      Engage the 3 guides as shown in the illustration.

    2. Engage the 2 clips to install the No. 2 instrument panel speaker panel sub-assembly as shown in the illustration.

  12. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  13. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Engage the 4 claws, 2 clips and 2 guides to install the No. 3 instrument panel register assembly.

  14. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. B001NPZ

      Engage the 5 claws as shown in the illustration.

    3. Install the 2 screws <E>.

    4. B001O9J

      Open the lower instrument panel sub-assembly door as shown in the illustration.

    5. Install the lower instrument panel sub-assembly with the 3 screws <E>.

  15. INSTALL INSTRUMENT PANEL BOX DOOR COVER


    1. B001OB4

      Engage the 4 claws to install the instrument panel box door cover as shown in the illustration.

    2. B001OGB

      Close the lower instrument panel sub-assembly door as shown in the illustration.

  16. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  17. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. B001NSR

      Engage the 2 guides, claw and 4 clips to install the No. 2 instrument panel under cover sub-assembly as shown in the illustration.

  18. INSTALL INSTRUMENT SIDE PANEL RH


    1. B001OL0

      Engage the 2 guides as shown in the illustration.

    2. B001ONB

      Engage the 2 claws and 4 clips to install the instrument side panel RH as shown in the illustration.

  19. INSTALL FRONT DOOR OPENING TRIM COVER RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  20. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  21. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  22. INSTALL REAR CONSOLE BOX ASSEMBLY

    Click here

  23. INSTALL MULTI-DISPLAY ASSEMBLY

    Click here

  24. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. B001NUF

      Engage the 2 clips and 5 guides as shown in the illustration.

    2. Install the center instrument cluster finish panel sub-assembly with the 2 clips.

  25. INSTALL SWITCH BASE


    1. for LHD:


      1. Connect the connector.

      2. Engage the 3 claws to install the switch base.

    2. for RHD:


      1. Connect the connector.

      2. Engage the 4 claws to install the switch base.

  26. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Engage the 6 claws and 2 guides to install the No. 1 instrument panel register assembly.

  27. INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect each connector.

    2. Engage the 4 claws to install the No. 1 switch hole base.

  28. INSTALL COMBINATION METER ASSEMBLY

    Click here

  29. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. for LHD:


      1. Connect each connector and engage each clamp.

      2. Engage the 12 claws, 2 clips and guide.

      3. Install the lower No. 1 instrument panel finish panel with the 2 bolts <B>.

    2. for RHD:


      1. Connect each connector and engage each clamp.

      2. Engage the 6 claws, 3 clips and guide.

      3. Install the lower No. 1 instrument panel finish panel with the 2 bolts <B>.

      4. B001NZP

        Engage the 2 claws to close the cover as shown in the illustration.

  30. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.

  31. INSTALL INSTRUMENT SIDE PANEL LH


    1. B001OLD

      Engage the 2 guides as shown in the illustration.

    2. B001NYD

      Engage the 2 claws and 4 clips to install the instrument side panel LH as shown in the illustration.

  32. INSTALL FRONT DOOR OPENING TRIM COVER LH

    Click here

  33. INSTALL COWL SIDE TRIM BOARD LH

    Click here

  34. INSTALL FRONT DOOR SCUFF PLATE LH

    Click here

  35. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET

    Click here

  36. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL


    1. B001O8T

      Engage the 2 claws and 5 clips to install the lower center instrument panel finish panel as shown in the illustration.

  37. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. Connect the connector.

    2. Engage the 11 claws and clip to install the No. 2 instrument panel register assembly.

      B001O3X

      Note

      When installing the No. 2 instrument panel register assembly, check that the wire harness is not caught between the No. 2 instrument panel register assembly and duct.

  38. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Connect the connector.

    2. Engage the 10 claws and 2 clips to install the center instrument cluster finish panel garnish.

      B001O98

  39. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. Connect the connector.

    2. B001NT7

      Engage the 5 claws and 2 guides as shown in the illustration.

    3. Install the instrument cluster finish panel sub-assembly with the 2 screws <E>.

  40. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Click here

  41. INSTALL UPPER STEERING COLUMN COVER

    Click here

  42. INSTALL LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  43. INSTALL LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Click here

  44. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  45. INSTALL HORN BUTTON ASSEMBLY

    Click here

  46. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    1. for Power Tilt and Power Telescopic Steering Column:


      1. Reset the auto away/return function setting to the previous condition by changing the customize parameter Click here.

  47. INSPECT SRS WARNING LIGHT

    Click here