CONDENSER INSTALLATION

PROCEDURE


  1. INSTALL COOLER CONDENSER ASSEMBLY


    1. B001OF6

      Engage the 2 guides as shown in the illustration.

    2. Install the cooler condenser assembly with the 4 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

      Tech Tips

      If the cooler condenser assembly is replaced with a new one, add compressor oil to the new cooler condenser assembly.

      Capacity
      40 cc (1.35 fl. oz)
      Compressor Oil
      ND-8 or equivalent

  2. CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY


    1. Remove the vinyl tape from the air conditioner tube and accessory assembly and the connecting part of the cooler condenser assembly.

    2. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.

      Compressor Oil
      ND-OIL 8 or equivalent

    3. Install the O-ring to the air conditioner tube and accessory assembly.

    4. Install the air conditioner tube and accessory assembly to the cooler condenser assembly with the bolt.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

  3. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE


    1. Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose and the connecting part of the cooler condenser assembly.

    2. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.

      Compressor Oil
      ND-OIL 8 or equivalent

    3. Install the O-ring to the No. 1 cooler refrigerant discharge hose.

    4. Install the No. 1 cooler refrigerant discharge hose to the cooler condenser assembly with the bolt.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

  4. INSTALL RADIATOR SIDE DEFLECTOR LH


    1. Engage the guide and 3 claws to install the radiator side deflector LH.

  5. INSTALL RADIATOR SIDE DEFLECTOR RH


    1. Engage the guide and 3 claws to install the radiator side deflector RH.

  6. INSTALL HOOD LOCK SUPPORT SUB-ASSEMBLY


    1. Install the hood lock support sub-assembly with the bolt.

    2. Engage the clamp.

    3. Connect the connector.

  7. INSTALL UPPER RADIATOR SUPPORT (for 2AR-FE)

    Click here

  8. INSTALL UPPER RADIATOR SUPPORT (for 2GR-FE)

    Click here

  9. INSTALL UPPER RADIATOR SUPPORT (for 6AR-FSE)

    Click here

  10. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

    Click here

  11. INSTALL FRONT BUMPER ENERGY ABSORBER

    Click here

  12. INSTALL HOOD LOCK ASSEMBLY

    Click here

  13. INSTALL INLET AIR CLEANER ASSEMBLY (for 2AR-FE)

    Click here

  14. INSTALL INLET AIR CLEANER ASSEMBLY (for 6AR-FSE)

    Click here

  15. INSTALL INLET NO. 1 AIR CLEANER (for 2GR-FE)

    Click here

  16. INSTALL INLET NO. 2 AIR CLEANER (for 2GR-FE)

    Click here

  17. INSTALL FRONT BUMPER ASSEMBLY

    Click here

  18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  19. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

    Click here

  20. WARM UP ENGINE

    Click here

  21. INSPECT FOR REFRIGERANT LEAK

    Click here

  22. ADJUST HOOD SUB-ASSEMBLY

    Click here