FRONT SHOCK ABSORBER REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front shock absorber assembly removal/installation are shown below.

Necessary Procedures After Procedure Performed
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment

  1. Clear zero point calibration data and system information.

  2. Perform yaw rate and acceleration sensor zero point calibration and store system information.

  • VSC disabled or malfunctions

  • DTCs are stored

  • Slip indicator light illuminates

  • ABS warning light illuminates

  • Theft deterrent system (tilt sensor)*1

Click here

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

  • Ultrasonic sensor detection angle

  • Ultrasonic sensor detection angle registration

  • Intelligent clearance sonar system

  • LEXUS parking assist-sensor system (w/ Intelligent Clearance Sonar System)

Click here

Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (w/ Parallel Parking Assist Function)

for Initialization: Click here

for Calibration: Click here

Parking assist monitor system (w/o Parallel Parking Assist Function)

for Initialization: Click here

for Calibration: Click here


  • Parking assist ECU initialization

  • Adjust steering angle

 Panoramic view monitor system

for Initialization: Click here

for Calibration: Click here

Initialize headlight ECU sub-assembly LH

  • Adaptive high beam system

  • Automatic headlight beam level control system

Click here

*1: w/ TFT Meter Type

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY

    Click here

  2. LOOSEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    1. B007X67

      Loosen the front support to front shock absorber nut.

      CAUTION:


      • Only loosen the front support to front shock absorber nut if the front shock absorber with coil spring needs to be disassembled.

      • Only loosen the front support to front shock absorber nut, do not remove it.

      • If the front support to front shock absorber nut is removed with the front coil spring under tension, components of the front shock absorber with coil spring may fly off.

      B007ZRH

  3. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    1. w/ Wiper Deicer System:


      1. B007Z0K

        Disconnect the connector.

      2. Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.

    2. w/ Heated Windshield Defroster System:


      1. B007Y7XC01
        B007Z37 Release the lock lever
        B007YXL Disconnect the connector

        Release the lock lever and disconnect the connectors.

      2. B007WM5

        Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.

    3. B007ZUK

      Disengage the clamp and separate the wire harness from the outer cowl top panel sub-assembly.

    4. B007Y9U

      Remove the 6 bolts, 6 nuts and outer cowl top panel sub-assembly.

  4. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    1. w/ Wiper Deicer System:


      1. B007Z08

        Disconnect the connector.

      2. Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.

    2. B007ZA7

      Disengage the clamp and separate the wire harness from the outer cowl top panel sub-assembly.

    3. B007X42

      Remove the 6 bolts, 6 nuts and outer cowl top panel sub-assembly.

  5. REMOVE FRONT WHEEL

    Click here

  6. SEPARATE FRONT STABILIZER LINK ASSEMBLY


    1. B007YNF

      Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.

      Note

      Do not damage the boot of the ball joint.

      Tech Tips

      If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.

  7. SEPARATE FRONT SPEED SENSOR (w/o AVS)


    1. B007X4KC03
      *a Sensor Clamp

      Disengage the 2 claws and separate the sensor clamp.

    2. Remove the bolt and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

      Note

      Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.

  8. SEPARATE FRONT SKID CONTROL SENSOR WIRE (w/ AVS)


    1. B00803P

      Disconnect the front speed sensor wire connector from the sensor bracket.

    2. Disconnect the AVS connector from the absorber control actuator.

    3. B007Y0YC01

      Remove the 2 bolts and separate the front skid control sensor wire and front flexible hose from the front shock absorber assembly.

      Note

      Be sure to separate the front skid control sensor wire and front flexible hose from the front shock absorber assembly completely.

  9. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING


    1. B007ZAMC02
      *a Wooden Block
      *b Jack
      B007WXX Front of the Vehicle
      B007ZL6 Wooden Block Placement Location

      Support the front lower No. 1 suspension arm sub-assembly using a jack and wooden block.

      Note

      Keep the front lower No. 1 suspension arm sub-assembly supported until installation of the front shock absorber with coil spring is complete.

    2. B007XM0

      Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

      Note


      • When removing the nuts, keep the bolts from rotating.

      • Use wire or an equivalent tool to hang the separated steering knuckle.

    3. B007Z35

      Remove the nut, 2 spacers and front shock absorber with coil spring.

  10. REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    1. B007WZVN04

      Secure SST in a vise.

      SST
      09727-00051   ( 09727-00010, 09727-00031 )

    2. Attach the hooks of each SST arm across the diameter of the coil spring.

      CAUTION:


      • B007WR1

        Make sure that the hooks are securely attached to the coil spring.

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

      • B007ZA1

        Make sure that the hooks of the upper and lower SST arms are attached to the coil spring so that the distance between the hooks is as large as possible.

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

      • B007ZQN

        Make sure that the arms of SST are parallel and the number of coils between the arms is the same on each side.

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

    3. Install the stopper pins to the hooks of SST.

      CAUTION:


      • Make sure that the stopper pins are installed securely.

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

      B007WYS
    4. B007YGTC03
      *a Vehicle Nut

      Install SST and 2 vehicle nuts to the upper support as shown in the illustration.

      SST
      09727-30022   ( 09727-00090, 09727-00100 )

    5. Using SST, compress the coil spring.

      CAUTION:


      • B007XFO

        If the coil spring starts to bow out while using SST, stop immediately and reattach SST correctly.

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

      • B007WPN

        Do not compress the coil spring to the point where the coils touch each other.

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

      • B007ZL4

        Do not use an impact wrench.

      • If an impact wrench is used, the threads of SST may be damaged, or sudden compression of the coil spring may cause a hook to disengage and the coil spring to fly out, resulting in injury.

      • B007Z7HN02

        If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.

      • If a stopper pin is removed, install a coil spring stopper belt as shown in the illustration.

      • If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

      SST
      09727-00110

    6. Check that the coil spring has become detached, and then remove the front support to front shock absorber nut.

      CAUTION:


      • Do not remove the front support to front shock absorber nut while the coil spring is under tension.

      • If the front support to front shock absorber nut is removed with the coil spring under tension, components of the front shock absorber with coil spring may fly off, resulting in injury.

      B00805F

  11. REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY


    1. Remove the front suspension support sub-assembly from the front shock absorber assembly.

  12. REMOVE FRONT SPRING SEAT SUB-ASSEMBLY WITH INSULATOR


    1. B007Z9UC02
      *1 Front Spring Seat Sub-assembly with Insulator
      *a Claw

      Disengage the front spring seat sub-assembly with insulator from the claws of the front shock absorber assembly.

    2. Remove the front spring seat sub-assembly with insulator from the front shock absorber assembly.

  13. REMOVE FRONT COIL SPRING


    1. Remove the front coil spring and SST.

      Note

      Do not use an impact wrench. It will damage SST.

  14. REMOVE FRONT SPRING BUMPER


    1. Remove the front spring bumper from the front shock absorber assembly.

  15. REMOVE FRONT LOWER COIL SPRING INSULATOR


    1. Remove the front lower coil spring insulator from the front shock absorber assembly.

  16. REMOVE FRONT SHOCK ABSORBER ASSEMBLY