PANORAMIC VIEW MONITOR SYSTEM, Diagnostic DTC:C1684

DTC Code DTC Name
C1684 Side Camera Current Malfunction

DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1684 Side Camera Current Malfunction Side camera current malfunction

  • Harness or connector

  • Parking assist ECU

  • Side television camera assembly RH (for LHD)

  • Outer rear view mirror assembly RH (for LHD)

  • Side television camera assembly LH (for RHD)

  • Outer rear view mirror assembly LH (for RHD)

WIRING DIAGRAM


  1. for LHD

    B006C30E18
    *a RCB+
    *b Side Television Camera Assembly RH
    *c Parking Assist ECU
    *d Outer Rear View Mirror Assembly RH

  2. for RHD

    B006C30E15

CAUTION / NOTICE / HINT

Note


  • When "!" mark is displayed on the multi-display assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

    Click here

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

    Click here

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTCs.

      Click here


      Chassis > Panoramic View Monitor > Clear DTCs

    2. Check for DTCs.

      Click here


      Chassis > Panoramic View Monitor > Trouble Codes
      OK
      DTC C1684 is not output.
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH) Click here

    B

  2. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)


    1. Disconnect the G95 parking assist ECU connector.

    2. Disconnect the H38 outer rear view mirror assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G95-40 (RCB+) - H38-2 (RCB+) Always Below 1 Ω
      G95-17 (RGND) - H38-1 (RGND) Always Below 1 Ω
      G95-40 (RCB+) or H38-2 (RCB+) - Body ground Always 10 kΩ or higher
      G95-17 (RGND) or H38-1 (RGND) - Body ground Always 10 kΩ or higher

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G95-40 (RCB+) or H38-2 (RCB+) - Body ground Engine switch on (IG) Below 1 V
      G95-17 (RGND) or H38-1 (RGND) - Body ground Engine switch on (IG) Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK PARKING ASSIST ECU


    1. B006BE1C94
      *a

      Component with harness connected

      (Parking Assist ECU)

      Disconnect the outer rear view mirror assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G95-17 (RGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G95-40 (RCB+) - G95-17 (RGND) Engine switch on (IG) 5.5 to 7.05 V
      G95-40 (RCB+) - G95-17 (RGND) Engine switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE PARKING ASSIST ECU Click here

    OK

  4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH


    1. B006G0IC10
      *a

      Component without harness connected

      (to Side Television Camera Assembly RH)
      *b

      Component without harness connected

      (to Outer Rear View Mirror Assembly RH)

      Disconnect the outer rear view mirror assembly RH connector.

    2. Disconnect the side television camera assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B-1 (SCB+) - 2 (RCB+) Always Below 1 Ω
      B-5 (SGND) - 1 (RGND) Always Below 1 Ω
      B-1 (SCB+) or 2 (RCB+) - Body ground Always 10 kΩ or higher
      B-5 (SGND) or 1 (RGND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH Click here

    OK

  5. CHECK SIDE TELEVISION CAMERA ASSEMBLY RH


    1. Replace the side television camera assembly RH with a new or normally functioning one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK FOR DTC


    1. Clear the DTCs.

      Click here


      Chassis > Panoramic View Monitor > Clear DTCs

    2. Check for DTCs.

      Click here


      Chassis > Panoramic View Monitor > Trouble Codes
      OK
      DTC C1687 is not output.
      Result
      Proceed to
      OK
      NG

    OK

    END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

    NG

    REPLACE PARKING ASSIST ECU Click here

  7. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)


    1. Disconnect the G95 parking assist ECU connector.

    2. Disconnect the H37 outer rear view mirror assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G95-12 (LCB+) - H37-2 (LCB+) Always Below 1 Ω
      G95-35 (LGND) - H37-1 (LGND) Always Below 1 Ω
      G95-12 (LCB+) or H37-2 (LCB+) - Body ground Always 10 kΩ or higher
      G95-35 (LGND) or H37-1 (LGND) - Body ground Always 10 kΩ or higher

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G95-12 (LCB+) or H37-2 (LCB+) - Body ground Engine switch on (IG) Below 1 V
      G95-35 (LGND) or H37-1 (LGND) - Body ground Engine switch on (IG) Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK PARKING ASSIST ECU


    1. B006BE1C93
      *a

      Component with harness connected

      (Parking Assist ECU)

      Disconnect the outer rear view mirror assembly LH connector

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G95-35 (LGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G95-12 (LCB+) - G95-35 (LGND) Engine switch on (IG) 5.5 to 7.05 V
      G95-12 (LCB+) - G95-35 (LGND) Engine switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE PARKING ASSIST ECU Click here

    OK

  9. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH


    1. B006G0IC01
      *a

      Component without harness connected

      (to Side Television Camera Assembly LH)
      *b

      Component without harness connected

      (to Outer Rear View Mirror Assembly LH)

      Disconnect the outer rear view mirror assembly LH connector.

    2. Disconnect the side television camera assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-1 (SCB+) - 2 (LCB+) Always Below 1 Ω
      A-5 (SGND) - 1 (LGND) Always Below 1 Ω
      A-1 (SCB+) or 2 (LCB+) - Body ground Always 10 kΩ or higher
      A-5 (SGND) or 1 (LGND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH Click here

    OK

  10. CHECK SIDE TELEVISION CAMERA ASSEMBLY LH


    1. Replace the side television camera assembly LH with a new or normally functioning one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  11. CHECK FOR DTC


    1. Clear the DTCs.

      Click here


      Chassis > Panoramic View Monitor > Clear DTCs

    2. Check for DTCs.

      Click here


      Chassis > Panoramic View Monitor > Trouble Codes
      OK
      DTC C1684 is not output.
      Result
      Proceed to
      OK
      NG

    OK

    END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

    NG

    REPLACE PARKING ASSIST ECU Click here