KNEE AIRBAG ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the lower No. 1 instrument panel airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The following procedure is for an LHD vehicle.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B007XYL

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    B007WSF

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  4. REMOVE COWL SIDE TRIM BOARD LH

    Click here

  5. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    Click here

  6. REMOVE INSTRUMENT PANEL GARNISH LH

    Click here

  7. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    Click here

  8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

    Click here

  9. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

    Click here

  10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    Click here

  11. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT

    Click here

  12. REMOVE LOWER INSTRUMENT FINISH PANEL SUB

    Click here

  13. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    CAUTION:

    When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.

    B007Y1BC02
    B007ZL6 Deployment Side

    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B007WSF
    3. B007ZERC01
      *a Hook
      *b Guide

      Remove the 2 bolts.

    4. Disengage the 3 claws, hook and 2 guides to separate the lower No. 1 instrument panel airbag assembly.

      Note

      When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.

    5. B007XS6C01
      *a Protective Tape
      *b Airbag Connector
      *c Airbag Connector Lock

      Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock.

    6. Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.