IMMOBILISER SYSTEM(w/o Entry and Start System) HOW TO PROCEED WITH TROUBLESHOOTING

DTC Code DTC Name
HOW TO PROCEED WITH TROUBLESHOOTING

CAUTION / NOTICE / HINT

Tech Tips


  • Use this procedure to troubleshoot the immobiliser system.

  • *: Use the GTS.

PROCEDURE


  1. VEHICLE BROUGHT TO WORKSHOP

    Result
    Proceed to
    NEXT

    NEXT
  2. CUSTOMER PROBLEM ANALYSIS

    Tech Tips


    • In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

    • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

    • The following 5 items are important points for problem analysis:

    What Vehicle model, system name
    When Date, time, occurrence frequency
    Where Whether the problem occurs at a specific location
    Under what conditions? Whether the doors were locked or unlocked, whether the ignition switch was on, whether the engine was running.
    How did it happen? Problem symptoms
    Result
    Proceed to
    NEXT

    NEXT
  3. INSPECT BATTERY VOLTAGE


    1. Measure the battery voltage.

      Standard Voltage
      11 to 14 V

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

      Result
      Proceed to
      NEXT

    NEXT
  4. CRANK ENGINE FOR MORE THAN 10 SECONDS

    Result
    Proceed to
    NEXT

    NEXT
  5. CHECK FOR DTC* (ECM)


    1. Check for DTCs and note any codes that are output.


      1. for 8NR-FTS:


        Powertrain > Engine > Trouble Codes
      2. for 3ZR-FAE:


        Powertrain > Engine and ECT > Trouble Codes

      Tech Tips

      Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

      Result
      Result Proceed to
      DTCs are not output A
      SFI system DTCs are output (for 8NR-FTS) B
      SFI system DTCs are output (for 3ZR-FAE) C
      Immobiliser system DTCs are output D

    B
    C
    D
    A
  6. CHECK FOR DTC* (TRANSPONDER KEY ECU ASSEMBLY)


    1. Check for DTCs and note any codes that are output.


      Body Electrical > Immobiliser > Trouble Codes

      Tech Tips

      Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

      Result
      Result Proceed to
      DTCs are not output A
      Immobiliser system DTCs are output B

    B
    A
  7. PROBLEM SYMPTOMS TABLE


    1. Refer to Problem Symptoms Table.

      Click here

      Result
      Result Proceed to
      Fault is not listed in problem symptoms table A
      Fault is listed in problem symptoms table B

    B
    A
  8. OVERALL ANALYSIS AND TROUBLESHOOTING*


    1. Data List / Active Test.

      Click here

    2. Terminals of ECU.

      Click here

      Result
      Proceed to
      NEXT

    NEXT
  9. REPAIR OR REPLACE

    Tech Tips

    If the transponder key ECU assembly, ECM, or key are replaced, refer to Service Bulletin.

    Result
    Proceed to
    NEXT

    NEXT
  10. CHECK FOR DTC*


    1. Clear the DTCs.


      Body Electrical > Immobiliser > Clear DTCs
      1. for 8NR-FTS:


        Powertrain > Engine > Clear DTCs
      2. for 3ZR-FAE:


        Powertrain > Engine and ECT > Trouble Codes
    2. Check for DTCs.


      Body Electrical > Immobiliser > Trouble Codes
      1. for 8NR-FTS:


        Powertrain > Engine > Trouble Codes
      2. for 3ZR-FAE:


        Powertrain > Engine and ECT > Trouble Codes

      Tech Tips

      Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

      Result
      Result Proceed to
      DTCs are not output A
      Immobiliser system DTCs are output B

    A
    B