SEAT HEATER CONTROL(for Front Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the seat heater control sub-assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

for 8GR-FKS: Click here

for V35A-FTS: Click here

Memorize steering angle neutral point LKA/LDA system

Click here

Parking support brake system*
Pre-collision system
Adaptive high beam system

    Lighting system (EXT)

  • Cornering lights
Variable gear ratio steering system

Click here

Parking assist monitor system

Click here

Panoramic View Monitor System

Click here

Initialize rear door sunshade system Rear door sunshade system

Click here

Initialize power trunk lid system Power trunk lid system

Click here


  • Power seat switch LH (Including removal and installation)

  • Power seat switch RH (Including removal and installation)

  • Front seat adjuster assembly LH (Including removal and installation,inspection)

  • Front seat adjuster assembly RH (Including removal and installation,inspection)

 Initialize position control ECU Front Power Seat Control System

Click here


    for Front Passenger Side with Occupant classification System:

  • Front seat assembly RH (Only for removal and installation)

  • Occupant detection ECU (Including removal and installation)

 Zero point calibration (Occupant classification system)

  • Occupant classification system

  • Passenger airbag ON/OFF indicator

  • Airbag system (Front passenger side)

  • Seat belt warning system (Front passenger)

Click here

*: When performing learning using the GTS.
Click here Click here

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

B006B4P

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. REMOVE FRONT SEAT ASSEMBLY

    Click here

  2. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Seat)

    Click here

  3. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Seat)

    Click here

  4. REMOVE FRONT POWER ADJUSTER SHIELD LH

    Click here

  5. REMOVE FRONT SEAT CUSHION SHIELD LH

    Click here

  6. REMOVE FRONT SEAT FRONT CUSHION SHIELD LH

    Click here

  7. REMOVE SEAT CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

    Click here

  8. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH


    1. B006AQL

      Disconnect the connector of the front vertical motor.

    2. B006D77C69
      *a

      Component without harness connected

      (Front Vertical Motor (Front Seat Adjuster Assembly LH))

      Connect the No. 1 terminal of the front vertical motor to the positive (+) battery terminal, and the No. 4 terminal to the negative (-) battery terminal and then raise the cushion height to the uppermost position.

      Note

      After performing this procedure, initialize the seat ECU (position control ECU assembly).

    3. B006G2F

      Disconnect the connector of the rear lifter motor.

    4. B006D77C33
      *a

      Component without harness connected

      (Rear Lifter Motor (Front Seat Adjuster Assembly))

      Connect the No. 1 terminal of the rear lifter motor to the positive (+) battery terminal, and the No. 4 terminal to the negative (-) battery terminal and then raise the cushion height to the uppermost position.

      Note

      After performing this procedure, initialize the seat ECU (position control ECU assembly).

    5. w/ Ottoman:


      1. B006FU3

        Disconnect the connector of the ottoman motor.

      2. B006D77C33
        *a

        Component without harness connected

        (Ottoman Motor (Front Seat Adjuster Assembly))

        Connect the No. 1 terminal of the ottoman motor to the positive (+) battery terminal, and the No. 4 terminal to the negative (-) battery terminal and then adjust the length of the cushion to the frontmost position.

        Note

        After performing this procedure, initialize the seat ECU (position control ECU assembly).

    6. Disconnect the connector.

    7. B006FCIC02
      B006DHE Remove in this Direction

      Detach the claw and remove the seat heater control sub-assembly LH.