NOISE FILTER(w/o Rear No. 2 Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during radio setting condenser removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B007WTA

Click here

PROCEDURE


  1. REMOVE TONNEAU COVER ASSEMBLY

    Click here

  2. REMOVE DECK BOARD ASSEMBLY

    Click here

  3. REMOVE REAR NO. 3 FLOOR BOARD

    Click here

  4. REMOVE SPARE WHEEL COVER (for Compact Spare Tire)

    Click here

  5. REMOVE REAR DECK FLOOR BOX (w/ Spare Tire)

    Click here

  6. REMOVE REAR FLOOR CARPET (w/o Spare Tire)

    Click here

  7. REMOVE REAR NO. 4 FLOOR BOARD (except Full Size Spare Tire)

    Click here

  8. REMOVE REAR NO. 4 FLOOR BOARD (for Full Size Spare Tire)

    Click here

  9. REMOVE FRONT DECK FLOOR BOX (w/ Spare Tire)

    Click here

  10. REMOVE DECK FLOOR BOX RH (w/o Spare Tire)

    Click here

  11. REMOVE DECK FLOOR BOX LH (w/o Spare Tire)

    Click here

  12. REMOVE DECK SIDE TRIM BOX RH (except Full Size Spare Tire)

    Click here

  13. REMOVE DECK SIDE TRIM BOX RH (for Full Size Spare Tire)

    Click here

  14. REMOVE REAR FLOOR FINISH PLATE

    Click here

  15. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  16. REMOVE REAR SEAT ASSEMBLY LH

    Click here

  17. REMOVE UPPER QUARTER TRIM PAD LH

    Click here

  18. REMOVE REAR SEAT SIDE GARNISH LH

    Click here

  19. REMOVE REAR FLOOR FINISH SIDE PLATE LH

    Click here

  20. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Click here

  21. REMOVE ROPE HOOK ASSEMBLY

    Click here

  22. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  23. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    Click here

  24. REMOVE RADIO SETTING CONDENSER

    Note

    When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.


    1. A01VTIH

      Remove the bolt.

    2. Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. A01VXLA

      Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.

    4. A01VW3K

      Using a screwdriver, bend back and break off the claw as shown in the illustration.

    5. Remove the terminal cover from the wire harness.

      Note


      • Make sure to hold the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

      • Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

      • Check for deformation of the terminal after the wire harness has been removed from the terminal cover.