REAR SEAT SIDE AIRBAG ASSEMBLY(w/o Rear No. 2 Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear seat airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point LKA/LDA System

Click here

Intelligent clearance sonar system*1
Pre-crash safety system

Lighting system (EXT)


  • Cornering lights
Adaptive high beam system
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Parking assist monitor system (w/ Parallel parking assist function)

Click here

Parking assist monitor system (w/o Parallel parking assist function)

Click here

Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Reset back door close position Power back door system

Click here

*1: When performing learning using the GTS.

Click here

CAUTION:


  • B007XYL

    Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

Note

If a rear seat airbag assembly has been deployed, replace the rear seat airbag assembly, rear seatback frame sub-assembly, separate type rear seatback pad and separate type rear seatback cover with the necessary parts in accordance with the extent of the collision damage.

for LH Side: Click here

for RH Side: Click here

PROCEDURE


  1. REMOVE REAR SEAT ASSEMBLY (for LH Side)

    Click here

  2. REMOVE REAR SEAT ASSEMBLY (for RH Side)

    Click here

  3. REMOVE REAR SEAT COVER CAP (for Manual Seat)

    Click here

  4. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)

    Click here

  5. REMOVE POWER SEAT SWITCH ASSEMBLY (for Power Seat)

    Click here

  6. DISCONNECT SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

    Click here

  7. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD (for LH Side)

    Click here

  8. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD (for RH Side)

    Click here

  9. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for RH Side)

    Click here

  10. REMOVE REAR SEATBACK COVER

    Click here

  11. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY

    Click here

  12. REMOVE SEAT BELT ANCHOR COVER CAP (for RH Side)

    Click here

  13. REMOVE REAR SEAT SHOULDER BELT COVER (for RH Side)

    Click here

  14. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for LH Side)

    Click here

  15. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for RH Side)

    Click here

  16. REMOVE SEATBACK FELT

    Click here

  17. REMOVE REAR SEAT AIRBAG ASSEMBLY

    CAUTION:

    When storing the rear seat airbag assembly, keep the airbag deployment side facing upward.

    B007ZMQC03
    B007ZL6 Deployment Side

    1. B007YJF

      for Manual Seat:


      1. Disengage the 3 clamps.

      2. Remove the 2 nuts and rear seat airbag assembly.

        Note


        • Do not reuse the nuts.

        • Make sure that the rear seatback frame sub-assembly is not deformed. If it is deformed, replace it with a new one.

    2. B007XGD

      for Power Seat:


      1. Disengage the 3 clamps.

      2. Remove the 2 nuts and rear seat airbag assembly.

        Note


        • Do not reuse the nuts.

        • Make sure that the rear seatback frame sub-assembly is not deformed. If it is deformed, replace it with a new one.