СИСТЕМА ЗАРЯДКИ ДВИГАТЕЛЯ, Diagnostic DTC:P162B

DTC Code DTC Name
P162B Lost Communication with Battery Monitor Module

DESCRIPTION

The ECM communicates with the battery state sensor assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P162B Lost Communication with Battery Monitor Module

Battery state sensor assembly or ECM communication stops for 33 seconds or more with the engine switch on (IG)

(1 trip detection logic)

  • Wire harness and connector

  • Battery state sensor assembly

  • ECM

 Charge warning light does not come on DTC stored

WIRING DIAGRAM

Refer to DTC P161A.

Click here

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • Before replacing the ECM, refer to Service Bulletin.

PROCEDURE


  1. CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION


    1. Check installation condition of the battery state sensor assembly.

      Result
      Result
      OK
      NG

    NG

    INSTALL THE BATTERY STATE SENSOR ASSEMBLY CORRECTLY Click here

    OK

  2. CHECK CHARGING SYSTEM


    1. Check the charging system.

      Click here

      Result
      Result
      OK
      NG

    NG

    REPAIR OR REPLACE CHARGING SYSTEM

    OK

  3. CHECK HARNESS AND CONNECTOR (ECM - BATTERY STATE SENSOR ASSEMBLY)


    1. Disconnect the D1 ECM connector.

    2. Disconnect the A5 battery state sensor assembly connector.

    3. Disconnect the D15 generator assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      A5-2 (LIN) or D15-2 (LIN) - D1-31 (LIN) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      A5-2 (LIN), D15-2 (LIN) or D1-31 (LIN) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    1. Check that the battery state sensor assembly connector is securely connected.

      OK
      The connector is securely connected.
    2. B006LWPC12
      *a

      Front view of wire harness connector

      (to Battery State Sensor Assembly)

      Disconnect the A5 battery state sensor assembly connector.

    3. Check the connector case and terminals for deformation or corrosion.

      OK
      No deformation or corrosion.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A5-1 (+B) - Body ground Always 11 to 14 V
      Result
      Result
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CLEAR DTCS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Check for DTCs, and note down any DTCs that are output.


      Powertrain > Engine > Trouble Codes

    6. Enter the following menus: Powertrain / Engine / Trouble Codes.

    7. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    8. Turn the engine switch off, wait 30 seconds.

      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK FOR DTCS


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Allow the engine to idle for approximately 17 minutes or more.

    4. Turn the GTS on.

    5. Enter the following menus: Powertrain / Engine / Trouble Codes.

    6. Check for DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      Only DTC P162B is output A
      DTC P161A and P162B are output. B
      DTCs are not output. C

    A

    REPLACE BATTERY STATE SENSOR ASSEMBLY Click here

    B

    REPLACE ECM Click here

    C

    CHECK FOR INTERMITTENT PROBLEMS Click here