CAUTION / NOTICE / HINT
CAUTION:
To prevent injury due to contact with an operating V-ribbed belt or cooling fan, keep your hands and clothing away from the V-ribbed belt and cooling fans when working in the engine compartment with the engine running or the engine switch on (IG).
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
PROCEDURE
CHECK BATTERY CONDITION
Note
If the battery is weak or if the engine is difficult to start, recharge the battery and perform inspections again before returning the vehicle to the customer.
Check the battery for damage or deformation. If severe damage, deformation or leakage is found, replace the battery.
Check the electrolyte level in each cell.
For maintenance-free batteries:
If the electrolyte level is below the lower line, replace the battery.
If the electrolyte level is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery.
Tech Tips
Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear window defogger, etc.).
For non-maintenance-free batteries:
If the electrolyte level is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte specific gravity.
Standard Specific Gravity |
---|
1.25 to 1.29 at 20°C (68°F) |
If the electrolyte level is above the lower line, check the battery voltage while cranking the engine. If the battery voltage is less than 9.6 V, recharge or replace the battery.
Tech Tips
Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear window defogger, etc.).
Check the voltage.
Turn the engine switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.
Measure the battery voltage according to the value(s) in the table below.
Standard Voltage | ||||||
---|---|---|---|---|---|---|
|
If the result is not as specified, recharge or replace the battery.
CHECK BATTERY TERMINAL
Check that the battery terminals are not loose or corroded.
If a terminal is loose or corroded, tighten or clean the terminal.
CHECK FUSES
Measure the resistance of each fuse for the charging system.
Tech Tips
Fuses related to the charging system are shown in System Diagram.
Standard Resistance |
---|
Below 1 Ω |
If the result is not as specified, replace the fuse.
INSPECT V-RIBBED BELT
INSPECT GENERATOR WIRING
Visually check the generator wiring.
Check that the wiring is in good condition.
CHECK FOR ABNORMAL NOISE
Check for abnormal noises from the generator assembly.
Check that no abnormal noises are heard from the generator assembly while the engine is running.
If noise occurs, refer to Problem Symptoms Table.
INSPECT CHARGE WARNING LIGHT
Turn the engine switch on (IG). Check that the charge warning light comes on.
Start the engine and check that the charge warning light turns off.
If the charge warning light does not operate as specified, perform troubleshooting of the charge warning light.
INSPECT CHARGING CIRCUIT WITHOUT LOAD
CAUTION:
To prevent injury due to contact with an operating V-ribbed belt or cooling fan, keep your hands and clothing away from the V-ribbed belt and cooling fans when working in the engine compartment with the engine running or the engine switch on (IG).
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
*1 | Generator Assembly |
*2 | Battery |
*a | Terminal B |
Connect a voltmeter and an ammeter to the charging circuit as follows.
Tech Tips
If a battery/generator assembly tester is available, connect the tester to the charging circuit in accordance with the manufacturer's instructions.
Disconnect the wire from terminal B of the generator assembly and connect it to the negative (-) lead of the ammeter.
Connect the ammeter positive (+) lead to terminal B of the generator assembly.
Connect the voltmeter positive (+) lead to the positive (+) terminal of the battery.
Ground the voltmeter negative (-) lead.
Check the charging circuit.
Maintain the engine speed at 2000 rpm and check the readings on the ammeter and voltmeter.
Standard Current |
---|
10 A or higher |
Standard Voltage |
---|
13.2 to 14.8 V |
If the result is not as specified, repair or replace the generator assembly.
INSPECT CHARGING CIRCUIT WITH LOAD
CAUTION:
To prevent injury due to contact with an operating V-ribbed belt or cooling fan, keep your hands and clothing away from the V-ribbed belt and cooling fans when working in the engine compartment with the engine running or the engine switch on (IG).
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
With the engine running at 2000 rpm, turn the high beam headlights on and turn the heater blower switch to the "HI" position.
Check the reading on the ammeter.
Standard Current |
---|
30 A or higher |
If the result is not as specified, repair or replace the generator assembly.
Tech Tips
If the battery is fully charged, the reading will sometimes be less than the standard current. In this case, add more electrical load (operate the wipers, rear window defogger, etc.) and check the reading on the ammeter again.