OCCUPANT DETECTION SENSOR(for Power Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • There is risk of injury.

B006C5U

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL REAR CENTER SEAT CUSHION PAD


    1. Install the rear center seat cushion pad to the center seat cushion frame sub-assembly.

    2. B0069VF

      Attach the claw and connect the connector of the occupant detection sensor.

  2. INSTALL REAR CENTER SEAT CUSHION COVER SUB-ASSEMBLY

    Click here

  3. INSTALL REAR SEAT CUSHION PAD LH (OCCUPANT DETECTION SENSOR)

  4. INSTALL REAR SEAT CUSHION PAD RH (OCCUPANT DETECTION SENSOR)

  5. INSTALL SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B006C6HC01
      B006DHE Install in this Direction

      Attach the hooks and install the seat cushion main stretcher cushion assembly.

    2. Clean the felt installation surface.


      1. When reusing the rear seat cushion pad LH, remove the felt remaining on the installation surface.

    3. B006CCCC01
      *a 2nd Step of The Bladder

      Install 2 new pieces of felt in the positions shown in the illustration.

      Note


      • The L-shaped joint must not stick out.

      • Do not cover the 2nd step of the bladder.

    4. B006FPEC01
      *a Orange Tube Color
      *b Green Tube Color
      *c Clear Tube Color

      Place the tube as shown in the illustration and using a tacker, install the strap with new tack pins.

  6. INSTALL SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)


    1. B006CU6C01
      B006DHE Install in this Direction

      Attach the hooks and install the seat cushion main stretcher cushion assembly.

    2. Clean the felt installation surface.


      1. When reusing the rear seat cushion pad LH, remove the felt remaining on the installation surface.

    3. B006BK4C01
      *a 2nd Step of The Bladder

      Install 2 new pieces of felt in the positions shown in the illustration.

      Note


      • The L-shaped joint must not stick out.

      • Do not cover the 2nd step of the bladder.

    4. B006BNYC01
      *a Yellow Tube Color
      *b Blue Tube Color
      *c Clear Tube Color

      Place the tube as shown in the illustration and using a tacker, install the strap with new tack pins.

  8. INSTALL SEAT CUSHION MAIN STRETCHER CUSHION ASSEMBLY (w/ Refresh Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL REAR SEAT CUSHION PAD (w/ Refresh Seat)


    1. Clean double-sided tape installation surface.


      1. When reusing the rear seat cushion pad, remove the double-sided tape remaining on the installation surface.

    2. Remove the peeling paper from the face of the rear seat cushion pad.

      Tech Tips

      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Install the rear seat cushion pad in the position shown in the illustration.

    4. Pull out the strap from the hole of the rear seat cushion pad.

      B006GKGC01
      *a Hog Ring Pliers - -
      B006FQ2 Double-sided Tape - -

    5. Using hog ring pliers, install the rear seat cushion pad with 4 new hog rings.

  10. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER LH

    Tech Tips

    Refer to the precautions on wrinkles to avoid creating any on the separate type rear seatback cover LH when installing the seat cover.

    Click here


    1. Install the separate type rear seat cushion cover LH to the rear seat cushion pad LH.

    2. Using hog ring pliers, securely install 14 new hog rings in the order shown in the illustration, and then install the separate type rear seat cushion cover LH to the rear seat cushion pad LH.

      B006GZ9C01
      *a Hog Ring Pliers - -

      Note


      • Do not dirty or damage the separate type rear seat cushion cover LH.

      • Be sure to securely tighten the hog rings as shown in the illustration while preventing wrinkles from forming on the center of the rear seat cushion pad LH and fabric.

  11. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD LH

    Click here

  13. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD RH

    Click here

  14. INSTALL SEAT CUSHION CHECK VALVE WITH HOSE LH (w/ Refresh Seat)

    Click here

  15. INSTALL SEAT CUSHION CHECK VALVE WITH HOSE RH (w/ Refresh Seat)

    Click here

  16. INSTALL REAR SEAT CUSHION LOCK HOOK

    Click here

  17. INSTALL REAR CENTER SEAT CUSHION ASSEMBLY

    Click here

  18. INSTALL REAR SEAT CUSHION ASSEMBLY LH

    Click here

  19. INSTALL REAR SEAT CUSHION ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here


    1. for 8GR-FKS:

      Click here

    2. for V35A-FTS:

      Click here

  21. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY

    Click here

  22. CHECK SRS WARNING LIGHT

    Click here

  23. INSPECT REAR SEAT ASSEMBLY

    Click here

  24. INSPECT SEAT HEATER SYSTEM

    Click here

  25. INSPECT CLIMATE CONTROL SEAT SYSTEM

    Click here

  26. INSPECT SEAT VIBRATION SYSTEM (w/ Refresh Seat)

    Click here

  27. INSPECT SEAT BELT WARNING SYSTEM


    1. w/ Occupant Classification System:

      Click here

    2. w/o Occupant Classification System:

      Click here