TRANSMISSION CONTROL CABLE INSTALLATION

PROCEDURE

1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

   1. Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

      5.0 N*m

      51 kgf*cm

      44 in.*lbf

   2. Connect the transmission control cable assembly to the rear engine mounting bracket with the bolt.

      5.0 N*m

      51 kgf*cm

      44 in.*lbf

   3. Connect the transmission control cable assembly to the control cable bracket with 2 new clips.

   4. Connect the transmission control cable assembly to the manual transaxle assembly with the 2 clips.

   5. 

      *a	Lock Piece
      *b	Stopper
      *c	Adjuster Case
      *d	Twist the stopper
      *e	Pull out
      *f	Return the stopper

      Release the lock of the transmission control select cable length adjustment structure.

      1. Twist the stopper.

      2. Pull the lock piece outward from the adjuster case to release the lock.

      3. Return the stopper.

   6. Engage the 2 claws to install the transmission control cable assembly to the floor shift lever assembly.

   7. Connect the transmission control shift cable to the floor shift lever assembly.

   8. Connect the transmission control select cable to the floor shift lever assembly and install the clip.

      Note:

      • Make sure the lock piece of the transmission control select cable length adjustment structure is facing upward when the transmission control select cable is connected.

      • Make sure that the transmission control select cable is securely installed.

   9. 

      *a	Press
      *b	Press and hold
      *c	Push in the shift and select lever pin

      Pressing the shift and select lever shaft and shift and select lever pin, push in the shift and select lever pin and check that the shift and select lever shaft is secured at the 1st-2nd gear position (the shaft comes to a stop at the position 8 mm (0.31 in.) below the neutral position).

   10. 

       *a	Slider Shaft
       *b	Cam Wall

       Push the slider shaft against the cam wall.

       Note:

       • Do not pull up the slider shaft.

       • When adjusting the transmission control select cable, make sure that the shift lever is not 1st or 2nd.

   11. Lock the transmission control select cable length adjustment structure.

       

       *a	Lock Piece	*b	Stopper
       *c	Adjuster Case	*d	Twist the stopper
       *e	Push	*f	Return the stopper

       1. Twist the stopper.

       2. Push the lock piece into the adjuster case with slider held against the cam wall.

          Note:

          • Securely press in the lock piece until the lock engages.

          • When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.

       3. Return the stopper to prevent the lock from being released.

          Note:

          • Push the lock piece as far as it will go.

          • Confirm whether the transmission control select cable length adjustment structure is locked securely.

   12. 

       *a

       Pull

       Release the shift and select lever pin that secures the shift and select lever shaft.

       1. Pull the shift and select lever pin toward the front left side of the vehicle.

2. INSTALL REAR CONSOLE BOX ASSEMBLY

   Click here

3. INSTALL NO. 1 FRONT FLOOR HEAT INSULATOR

   1. Install the No. 1 front floor heat insulator to the body with the 3 nuts.

      5.5 N*m

      56 kgf*cm

      49 in.*lbf

4. INSTALL FRONT EXHAUST PIPE ASSEMBLY

   Click hereClick here

5. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

   Click here

6. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

7. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

   Click here

8. INSTALL BATTERY TRAY

   Click here

9. INSTALL BATTERY

   Click here

10. INSPECT FOR EXHAUST GAS LEAK