SFI SYSTEM(w/o Canister Pump Module), Diagnostic DTC:P21CF13, P21D013, P21D113, P21D213

DTC Code DTC Name
P21CF13 Cylinder 1 Injector "B" Circuit Open
P21D013 Cylinder 2 Injector "B" Circuit Open
P21D113 Cylinder 3 Injector "B" Circuit Open
P21D213 Cylinder 4 Injector "B" Circuit Open

DESCRIPTION

The D-4S system has two injection systems. One is an in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The other is an intake port injection system. The ECM determines the percentage of direct injection and port injection necessary in accordance with the engine speed and load.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P21CF13 Cylinder 1 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).

  • Open or short in port fuel injector assembly circuit

  • Port fuel injector assembly

  • ECM

 Comes on DTC stored SAE Code: P21CF
P21D013 Cylinder 2 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).

  • Open or short in port fuel injector assembly circuit

  • Port fuel injector assembly

  • ECM

 Comes on DTC stored SAE Code: P21D0
P21D113 Cylinder 3 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).

  • Open or short in port fuel injector assembly circuit

  • Port fuel injector assembly

  • ECM

 Comes on DTC stored SAE Code: P21D1
P21D213 Cylinder 4 Injector "B" Circuit Open Open or short in port fuel injector assembly (1 trip detection logic).

  • Open or short in port fuel injector assembly circuit

  • Port fuel injector assembly

  • ECM

 Comes on DTC stored SAE Code: P21D2

MONITOR DESCRIPTION

The ECM monitors the injection control of the port fuel injector assemblies. If a malfunction is detected in a port fuel injector assembly circuit, the ECM cancels the injection control for the corresponding cylinder, illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Port fuel injector assembly (cylinder 1 to 4)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the ignition switch off and wait for at least 30 seconds.

  6. Start the engine.

  7. Idle the engine for 3 minutes or more [A].

  8. Turn the GTS on.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [B].

  10. Read the DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P21CF13, P21D013, P21D113 or P21D213.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    Tech Tips


    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system has a malfunction.

    • If the judgment result is INCOMPLETE, perform steps [A] through [B] again.

WIRING DIAGRAM

B00846YE01

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK DTCS OUTPUT (IN ADDITION TO DTC P21CF13, P21D013, P21D113 OR P21D213)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P21CF13, P21D013, P21D113 or P21D213 is output A
      DTC P21CF13, P21D013, P21D113 and P21D213 are output B

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 NO. 1 RELAY - PORT FUEL INJECTOR ASSEMBLY)

    A

  2. CHECK TERMINAL VOLTAGE (POWER SOURCE OF PORT FUEL INJECTOR ASSEMBLY)

    B008698C01
    *a

    Front view of wire harness connector

    (to Port Fuel Injector Assembly)
    *b No. 1 Cylinder
    *c No. 2 Cylinder
    *d No. 3 Cylinder
    *e No. 4 Cylinder

    1. Disconnect the port fuel injector assembly connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below

      Standard Voltage
      Tester Connection Condition Specified Condition
      F2-1 (#1) - Body ground Ignition switch ON 11 to 14 V
      F5-1 (#2) - Body ground Ignition switch ON 11 to 14 V
      F8-1 (#3) - Body ground Ignition switch ON 11 to 14 V
      F11-1 (#4) - Body ground Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 NO. 1 RELAY - PORT FUEL INJECTOR ASSEMBLY)

    OK

  3. CHECK HARNESS AND CONNECTOR (PORT FUEL INJECTOR ASSEMBLY - ECM)


    1. Disconnect the ECM connector.

    2. Disconnect the port fuel injector assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F2-2 (#10) - C57-76 (#10) Always Below 1 Ω
      F5-2 (#20) - C57-75 (#20) Always Below 1 Ω
      F8-2 (#30) - C57-74 (#30) Always Below 1 Ω
      F11-2 (#40) - C57-73 (#40) Always Below 1 Ω
      F2-2 (#10) or C57-76 (#10) - Body ground and other terminals Always 10 kΩ or higher
      F5-2 (#20) or C57-75 (#20) - Body ground and other terminals Always 10 kΩ or higher
      F8-2 (#30) or C57-74 (#30) - Body ground and other terminals Always 10 kΩ or higher
      F11-2 (#40) or C57-73 (#40) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT PORT FUEL INJECTOR ASSEMBLY (RESISTANCE)


    1. Inspect the port fuel injector assembly.

      Click here

      Tech Tips

      Perform "Inspection After Repair" after replacing the port fuel injector assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPLACE PORT FUEL INJECTOR ASSEMBLY Click here