CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) ECM Communication Stop Mode

DTC Code DTC Name
ECM Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

ECM Communication Stop Mode

Either condition is met:

  • "ECM (Engine)" is not displayed on the CAN Bus Check screen of the GTS

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "ECM Communication Stop Mode" in "DTC Combination Table" are output

    Click here

  • ECM main line or connector

  • Power source circuit of ECM

  • ECM ground circuit

  • ECM

WIRING DIAGRAM

C275804E12
C333589E03
C331763C01
C329846E02
C329846E01
C331763E01
C275805E11
C328235C01
C329850E02
C329850E01
C328235E05

CAUTION / NOTICE / HINT

Note:

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

  • DTC check procedure: Turn the ignition switch to ON and wait 20 seconds or more, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tip:

  • Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

  1. CHECK VEHICLE TYPE

    1. Check vehicle type.

    Result

    Result

    Result

    Proceed to

    for 1NR-FE, 1ZR-FAE, 1ZR-FE or 2ZR-FE

    A

    for 1ND-TV with Glow Plug Controller

    B

    for 1WW

    C

    for 8NR-FTS

    D
    B

    CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)Click here

    C

    CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)Click here

    D

    CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)Click here

    A

  2. CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)

    1. Disconnect the cable from the negative (-) battery terminal.

    2. C243831C54

      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the A50 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A50-13 (CANH) - A50-26 (CANL)

      Cable disconnected from negative (-) battery terminal

      108 to 132 Ω

    Result

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)

    OK

  3. CHECK ECM POWER SOURCE CIRCUIT

    1. Check the ECM power source circuit.

    Result

    Result

    Proceed to

    OK (for 1NR-FE)

    A

    OK (for 1ZR-FAE)

    B

    OK (for 1ZR-FE)

    C

    OK (for 2ZR-FE)

    D

    NG

    E
    A

    REPLACE ECM

    Click here

    B

    REPLACE ECM

    Click here

    C

    REPLACE ECM

    Click here

    D

    REPLACE ECM

    Click here

    E

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

  4. CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)

    1. Disconnect the cable from the negative (-) battery terminal.

    2. C243831C58

      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the A169 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A169-26 (CANH) - A169-25 (CANL)

      Cable disconnected from negative (-) battery terminal

      108 to 132 Ω

    Result

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)

    OK

  5. CHECK ECM POWER SOURCE CIRCUIT

    1. Check the ECM power source circuit.

      Click here

    Result

    Result

    Result

    OK

    NG
    OK

    REPLACE ECM

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

  6. CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)

    1. Disconnect the cable from the negative (-) battery terminal.

    2. C243831C55

      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the A50 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A50-26 (CANH) - A50-25 (CANL)

      Cable disconnected from negative (-) battery terminal

      108 to 132 Ω

    Result

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)

    OK

  7. CHECK ECM POWER SOURCE CIRCUIT

    1. Check the ECM power source circuit.

      Click here

    Result

    Result

    Result

    OK

    NG
    OK

    REPLACE ECM

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

  8. CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)

    1. Disconnect the cable from the negative (-) battery terminal.

    2. C243831C60

      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the A173 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A173-13 (CANH) - A173-26 (CANL)

      Cable disconnected from negative (-) battery terminal

      108 to 132 Ω

    Result

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)

    OK

  9. CHECK ECM POWER SOURCE CIRCUIT

    1. Check the ECM power source circuit.

      Click here

    Result

    Result

    Result

    OK

    NG
    OK

    REPLACE ECM

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)