OUTER MIRROR SWITCH INSPECTION

PROCEDURE


  1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)


    1. Check the mirror select switch and mirror surface adjust switch.


      1. B0085E7C06
        *a Mirror Select and Surface Adjust Switch
        *b

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        15 (M+) - 12 (E) Mirror surface adjust switch pushed up 90 to 110 Ω
        Mirror surface adjust switch pushed down 437 to 503 Ω
        Mirror surface adjust switch pushed left 744 to 856 Ω
        Mirror surface adjust switch pushed right 225 to 275 Ω
        Mirror surface adjust switch not pushed 10 kΩ or higher
        13 (MSW) - 12 (E) Mirror select switch turned to R position Below 1 Ω
        Mirror select switch turned to L position 90 to 110 Ω
        Mirror select switch off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check that the LED illuminates.


      1. B0085E7C05
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        OK
        Battery Connection Specified Condition

        Battery positive (+) - 14 (ILL+)

        Battery negative (-) - 16 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.

  2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)


    1. Check the mirror select switch and mirror surface adjust switch. (for LHD, w/ Power Retract Mirror)


      1. B0083W6C01
        *a Mirror Select and Surface Adjust Switch
        *b Retractable Outer Mirror Switch
        *c

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Condition Specified Condition

        10 (VL) - 7 (B)

        13 (M+) - 5 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        10 (VL) - 5 (E)

        13 (M+) - 7 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        9 (HL) - 7 (B)

        13 (M+) - 5 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        9 (HL) - 5 (E)

        13 (M+) - 7 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Condition Specified Condition

        12 (VR) - 7 (B)

        13 (M+) - 5 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        12 (VR) - 5 (E)

        13 (M+) - 7 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 7 (B)

        13 (M+) - 5 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 5 (E)

        13 (M+) - 7 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check the mirror retract switch. (for LHD, w/ Power Retract Mirror)


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        4 (MF) - 5 (E) Extend position 10 kΩ or higher
        Except extend position Below 1 Ω
        6 (MR) - 5 (E) Retract position 10 kΩ or higher
        Except retract position Below 1 Ω

        If the result is not as specified, replace the outer mirror switch assembly.

    3. Check the mirror select switch and mirror surface adjust switch. (for LHD, w/o Power Retract Mirror)


      1. B0086XQC23
        *a Mirror Select and Surface Adjust Switch
        *b

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Condition Specified Condition

        10 (VL) - 7 (B)

        13 (M+) - 15 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        10 (VL) - 15 (E)

        13 (M+) - 7 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        9 (HL) - 7 (B)

        13 (M+) - 15 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        9 (HL) - 15 (E)

        13 (M+) - 7 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Condition Specified Condition

        12 (VR) - 7 (B)

        13 (M+) - 15 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        12 (VR) - 15 (E)

        13 (M+) - 7 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 7 (B)

        13 (M+) - 15 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 15 (E)

        13 (M+) - 7 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    4. Check that the LED illuminates. (for LHD)


      1. B0087G6C01
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        OK
        Battery Connection Specified Condition

        Battery positive (+) - 8 (ILL+)

        Battery negative (-) - 14 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.

    5. Check the mirror select switch and mirror surface adjust switch. (for RHD, w/ Power Retract Mirror)


      1. B0085D5C01
        *a Mirror Select and Surface Adjust Switch
        *b Retractable Outer Mirror Switch
        *c

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Condition Specified Condition

        12 (VL) - 15 (B)

        9 (M+) - 1 (E)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        12 (VL) - 1 (E)

        9 (M+) - 15 (B)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        13 (HL) - 15 (B)

        9 (M+) - 1 (E)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        13 (HL) - 1 (E)

        9 (M+) - 15 (B)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Condition Specified Condition

        10 (VR) - 15 (B)

        9 (M+) - 1 (E)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        10 (VR) - 1 (E)

        9 (M+) - 15 (B)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        11 (HR) - 15 (B)

        9 (M+) - 1 (E)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        11 (HR) - 1 (E)

        9 (M+) - 15 (B)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    6. Check the mirror retract switch. (for RHD, w/ Power Retract Mirror)


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        2 (MF) - 1 (E) Extend position 10 kΩ or higher
        Except extend position Below 1 Ω
        16 (MR) - 1 (E) Retract position 10 kΩ or higher
        Except retract position Below 1 Ω

        If the result is not as specified, replace the outer mirror switch assembly.

    7. Check the mirror select switch and mirror surface adjust switch. (for RHD, w/o Power Retract Mirror)


      1. B0086XQC24
        *a Mirror Select and Surface Adjust Switch
        *b

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Condition Specified Condition

        12 (VL) - 15 (B)

        9 (M+) - 7 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        12 (VL) - 7 (E)

        9 (M+) - 15 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        13 (HL) - 15 (B)

        9 (M+) - 7 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        13 (HL) - 7 (E)

        9 (M+) - 15 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Condition Specified Condition

        10 (VR) - 15 (B)

        9 (M+) - 7 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        10 (VR) - 7 (E)

        9 (M+) - 15 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 15 (B)

        9 (M+) - 7 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 7 (E)

        9 (M+) - 15 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    8. Check that the LED illuminates. (for RHD)


      1. B0087G6C03
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        OK
        Battery Connection Specified Condition

        Battery positive (+) - 14 (ILL+)

        Battery negative (-) - 8 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.