ROOF HEADLINING REMOVAL

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE

  1. PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click hereClick here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click hereClick here

  3. REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/ Partition Net)

    1. B435736

      Release the 4 locks and remove the package tray trim pocket sub-assembly.

  4. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

    1. B435737

      Release the 2 locks and remove the tonneau cover assembly.

  5. REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire, for Compact Spare Tire)

    1. B435738

      Remove the deck board assembly.

  6. REMOVE DECK BOARD ASSEMBLY (for Full Size Spare Tire)

    1. B435739

      Remove the deck board assembly.

  7. REMOVE DECK FLOOR BOX LH

    B423641

    1. Using a clip remover, remove the 2 clips.

    2. Detach the 4 claws and remove the deck floor box LH.

  8. REMOVE REAR NO. 3 FLOOR BOARD

    1. for Compact Spare Tire:

      1. B435735

        Detach the 2 clips and 2 guides and remove the rear No. 3 floor board.

    2. for Full Size Spare Tire:

      1. B435734

        Detach the 4 clips and remove the rear No. 3 floor board.

  9. REMOVE REAR NO. 2 FLOOR BOARD

    Tip:

    Use the same procedure described for the rear No. 3 floor board side.

  10. REMOVE REAR FLOOR FINISH PLATE (w/o Spare Tire, for Compact Spare Tire)

    B337886

    1. Detach the 2 claws, 4 clips and 2 guides and remove the rear floor finish plate.

  11. REMOVE REAR DECK TRIM COVER (for Full Size Spare Tire)

    1. B435740

      Detach the 3 claws and 4 clips and remove the rear deck trim cover.

  12. REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (w/o Spare Tire, for Compact Spare Tire)

    1. Open the rear No. 1 floor board.

    2. B423642

      Remove the 4 screws.

    3. Detach the 4 clips and remove the rear No. 1 floor mat support side plate together with the rear No. 1 floor board.

  13. REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (for Full Size Spare Tire)

    1. Open the rear No. 1 floor board.

    2. B337889

      Remove the 4 screws.

    3. Detach the 4 clips and remove the rear No. 1 floor mat support side plate together with the rear No. 1 floor board.

  14. REMOVE REAR SEAT ASSEMBLY

    for LH Side:

    Click here

    for RH Side:

    Click here

  15. REMOVE FRONT DOOR SCUFF PLATE LH

    1. B337826

      Detach the 8 claws and 2 clips and remove the front door inside scuff plate LH.

  16. REMOVE FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure described for the LH side.

  17. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    1. B337906

      Remove the front door opening trim weatherstrip LH.

  18. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tip:

    Use the same procedure described for the LH side.

  19. REMOVE REAR DOOR SCUFF PLATE LH

    1. B337896

      Detach the 2 claws and 6 clips and remove the rear door scuff plate LH.

  20. REMOVE REAR DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure described for the LH side.

  21. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    B337907

    1. Remove the rear door opening trim weatherstrip LH.

  22. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tip:

    Use the same procedure described for the LH side.

  23. REMOVE DECK TRIM SERVICE HOLE COVER

    Tip:

    Use the same procedure for both deck trim service hole covers.

    1. B435732C01

      *1

      Protective Tape

      Using a screwdriver, detach the 4 claws and 2 guides and disconnect the deck trim service hole cover.

  24. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    1. Remove the screw and 2 bolts.

    2. Open the tether anchor set bracket cover.

    3. Remove the bolt and tether anchor set bracket.

    4. Remove the bolt and luggage hold belt striker assembly.

    5. Detach the 6 claws and 4 clips and remove the deck trim side panel assembly LH.

    6. Disconnect the connector.

      B423643

  25. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

    1. Remove the screw and 2 bolts.

    2. Open the tether anchor set bracket cover.

    3. Remove the bolt and tether anchor set bracket.

    4. Remove the bolt and luggage hold belt striker assembly.

    5. Detach the 6 claws and 4 clips and remove the deck trim side panel assembly RH.

      B423644

  26. REMOVE SEAT BELT ANCHOR COVER CAP

    Click here

  27. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

    1. B337894

      Remove the bolt and disconnect the rear seat outer belt shoulder anchor.

    2. B337895

      Detach the 8 clips and remove the inner roof side garnish assembly LH.

  28. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  29. REMOVE SHOULDER BELT ANCHOR COVER RH

    Click here

  30. REMOVE OUTER LAP BELT ANCHOR COVER

    Click here

  31. REMOVE LOWER CENTER PILLAR GARNISH LH

    1. B337898

      Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. B337897

      Detach the 2 clips and 2 claws and remove the lower center pillar garnish LH.

  32. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  33. REMOVE CENTER PILLAR GARNISH LH

    1. B337899

      Remove the 2 clips.

    2. Detach the clip and remove the center pillar garnish LH.

    3. Pass the front seat outer belt floor anchor through the hole of the center pillar garnish LH.

  34. REMOVE CENTER PILLAR GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  35. REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

    1. B337789

      Pull the upper part of the front pillar garnish LH toward the inside of the cabin and detach the 2 clips.

    2. Detach the 3 guides and remove the front pillar garnish LH.

  36. REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

    Tip:

    Use the same procedure described for the LH side.

  37. REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

    1. B337791C01

      *1

      Front Pillar Garnish Clip

      Pull the upper part of the front pillar garnish LH toward the inside of the cabin and detach the 2 front pillar garnish clips.

      Tip:

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. B337793C01

      *1

      Front Pillar Garnish Clip
      V100155

      Protective Tape

      Turn the ends of the 2 front pillar garnish clips 90° with needle-nose pliers and disconnect them from the front pillar garnish LH.

      Tip:

      Tape the tips of the needle-nose pliers before use.

    3. Detach the 3 guides and remove the front pillar garnish LH.

    4. B422591N02

      While pulling the front pillar garnish clip in direction A with a finger, insert a screwdriver at the position shown in the illustration.

    5. B422592N02

      While pulling the front pillar garnish clip in direction B with a finger, insert a screwdriver at the position shown in the illustration to detach the front pillar garnish clip.

      Note:

      If the front pillar garnish clip is damaged, replace it with a new one.

    6. B337795C01

      *1

      Curtain Shield Airbag Assembly LH

      *2

      Protective Cover
      V100155

      Adhesive Tape

      Protect the curtain shield airbag assembly LH.

      1. Completely cover the curtain shield airbag assembly LH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note:

        Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish assembly LH is removed.

  38. REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

    Tip:

    Use the same procedure described for the LH side.

  39. REMOVE UPPER INSTRUMENT PANEL

    Click here

  40. REMOVE VISOR ASSEMBLY LH

    1. B337900

      Remove the 2 screws and visor assembly LH.

  41. REMOVE VISOR ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  42. REMOVE VISOR HOLDER

    Tip:

    Use the same procedure for both visor holders.

    1. B337901

      Turn the visor holder clockwise approximately 45° and pull it as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  43. REMOVE MAP LIGHT ASSEMBLY

    Click here

  44. REMOVE ASSIST GRIP SUB-ASSEMBLY

    Tip:

    Use the same procedure for all assist grips.

    1. B337904C01
      V100155

      Protective Tape

      Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tip:

      Tape the screwdriver tip before use.

    2. B337905

      Detach the 2 clips and remove the assist grip sub-assembly.

  45. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

    Click here

  46. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  47. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  48. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  49. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  50. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

    1. B423645

      Remove the sun roof opening trim moulding.

  51. REMOVE ROOF HEADLINING ASSEMBLY

    1. B439427

      w/ EC Mirror:

      Disconnect the connector.

    2. B439428

      w/ Rain Sensor, w/o Pre-crash Safety System:

      Disconnect the connector.

    3. B439429

      w/ Rain Sensor, w/ Pre-crash Safety System:

      Disconnect the connector.

    4. w/ Pre-crash Safety System:

      1. B478380

        w/o Camera Heater:

        Disconnect the 2 connectors.

      2. B478369

        w/ Camera Heater:

        Disconnect the 3 connectors.

    5. B423646

      w/ Sliding Roof:

      Disconnect the connector.

    6. B337911

      Disconnect the connector from the rear pillar RH.

    7. B337909

      Disconnect the 2 connectors and detach the 3 clips and 3 wire harness clamps from the front pillar LH.

    8. B337910

      Detach the 4 wire harness clamps from the front pillar RH.

    9. w/o Sliding Roof:

      1. B423647

        Remove the 5 clips.

      2. Remove the roof headlining assembly as shown in the illustration.

        Note:

        Be careful not to damage the roof headlining assembly when taking it out.

        B423649

    10. w/ Sliding Roof:

      1. B423648

        Remove the 3 clips.

      2. Remove the roof headlining assembly as shown in the illustration.

        Note:

        Be careful not to damage the roof headlining assembly when taking it out.

        B423650

  52. REMOVE FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    1. B337917

      Detach the 4 clips and remove the front side rail spacer LH.

  53. REMOVE FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tip:

    Use the same procedure described for the LH side.

  54. REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    1. B337918

      Detach the 4 clips and remove the rear side rail spacer LH.

  55. REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tip:

    Use the same procedure described for the LH side.

  56. REMOVE REAR SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)

    Tip:

    When removing or replacing the rear side rail spacer LH, be sure to remove the curtain shield airbag assembly LH.

    Click here

    1. B337926

      Remove the bolt.

    2. Detach the clip and remove the rear side rail spacer LH.

  57. REMOVE REAR SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

    Tip:

    Use the same procedure described for the LH side.

  58. REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    1. B337919

      Detach the 3 clips and remove the No. 2 rear side rail spacer LH.

  59. REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tip:

    Use the same procedure described for the LH side.

  60. REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)

    B337920C01

    *1

    Pin

    *2

    Clip

    1. Using needle-nose pliers, release the lock by pinching the 2 locks of the pin, and pull out the pin from the clip.

    2. B337922

      Using 2 screwdrivers, detach the 2 claws by inserting the screwdrivers into the grooves of the clip as shown in the illustration, and then remove the clip from the vehicle body and disconnect the rear part of the curtain shield airbag assembly LH.

    3. B337925

      Detach the wire harness clamp.

    4. Detach the 2 clips and remove the rear No. 2 side rail spacer LH.

  61. REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

    Tip:

    Use the same procedure described for the LH side.