CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM, Diagnostic DTC:P2757

DTC Code DTC Name
P2757 Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance (Shift Solenoid Valve DSU)

DESCRIPTION

The ECM uses the lock-up control solenoid (DSU) to perform lock-up control in response to the driving conditions.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P2757

Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance (Shift Solenoid Valve DSU)

  1. Diagnosis Condition

    • The shift lever is in D, and the vehicle is being driven at a speed of 8 km/h (5.0 mph) or more.

  3. Malfunction Status

    • The lock-up signal is on, but lock-up is off.

  5. Malfunction Time

    • -

  7. Other

    • 2-trip detection logic

  1. Diagnosis Condition

    • The shift lever is in D, and the vehicle is being driven at a speed of 8 km/h (5.0 mph) or more.

  3. Malfunction Status

    • The lock-up signal is off, but lock-up is on.

  5. Malfunction Time

    • -

  7. Other

    • 2-trip detection logic

  • Torque converter assembly

  • Continuously variable transaxle assembly

Comes on

DTC stored

MONITOR DESCRIPTION

When performing lock-up control (on/off) of the torque converter, the ECM compares the rotating speeds of the turbine (NT) and engine (NE) to detect mechanical malfunctions in the lock-up control solenoid (DSU). When the rotating speeds are different, the ECM detects the problem, illuminates the MIL and stores this DTC.

PROCEDURE

  1. CHECK DTC OUTPUT (IN ADDITION TO DTC P2757)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    5. Read the DTCs using the GTS.

      Tip:

      If any DTCs other than P2757 are output, perform troubleshooting for those DTCs first.

    Result

    Result

    Proceed to

    Only DTC P2757 is output

    A

    DTC P2757 and other DTCs are output

    B
    B

    GO TO DTC CHART

    Click hereClick hereClick here

    A

  2. CLEAR DTC

    1. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    Result

    Proceed to

    NEXT
    NEXT

  3. PERFORM ROAD TEST

    CAUTION:

    Strictly observe posted speed limits, traffic laws and road conditions when performing the road test.

    Note:

    • This test must be conducted after checking and confirming that the engine is operating normally.

    • Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).

    • Perform this test with the A/C off.

    Tip:

    • Lock-up control will not operate when the CVT fluid temperature is 40°C (104°F) or less and the vehicle speed is 60 km/h (37 mph) or less, or when the CVT fluid temperature is 5°C (41°F) or less.

    • Lock-up control will not operate when the engine coolant temperature is 30°C (86°F) or less.

    • The lock-up off vehicle speed may vary depending on electrical load, and air conditioning and brake operations.

    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn on the GTS.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / SPD (NT), Lock Up and Engine Speed.

      Powertrain > Engine and ECT > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Engine Speed

      Engine speed

      min.: 0 rpm

      max.: 16383 rpm

      600 to 700 rpm: Idling

      When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.

      SPD (NT)

      Input turbine speed

      min.: 0 rpm

      max.: 12750 rpm

      • Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (After warming up engine)

      • Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (Idling with shift lever in P or N)

      • 0 rpm: Vehicle stopped with shift lever in R

      Data is displayed in increments of 50 rpm.

      Lock Up

      Lock-up

      OFF or ON

      • ON: Lock-up operating

      • OFF: Lock-up not operating

      -

    5. Check the Data List while driving.

    Result

    Result

    Proceed to

    When lock-up is ON, the turbine speed is less than the engine speed.

    A

    When lock-up is OFF, the turbine speed is equal to the engine speed.

    When lock-up is ON, the turbine speed is equal to the engine speed.

    B

    When lock-up is OFF, the turbine speed is less than the engine speed.
    B

    CHECK FOR INTERMITTENT PROBLEMS

    Click here

    A

  4. REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY AND TORQUE CONVERTER ASSEMBLY

    1. Replace the continuously variable transaxle assembly and torque converter assembly.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  5. PERFORM INITIALIZATION

    Note:

    • Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:

      Replaced Part

      • Continuously variable transaxle assembly

      • ECM

      • Oil pressure sensor

      • Airbag sensor assembly (Yaw rate and acceleration sensor)

    • After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.

    • Always perform calibration with the vehicle on level ground.

    • Do not shake or vibrate the vehicle during calibration.

    1. Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.

      Click hereClick here

    2. Check for DTCs again.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    END