COMBINATION SWITCH INSPECTION

PROCEDURE


  1. INSPECT SATELLITE SWITCH SET (w/ AVS)


    1. B006E36C06
      *a

      Component without harness connected

      (Satellite Switch Set)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G49-3 (P) - G49-7 (GND) Satellite switch set knob turned and held at S/S+ position Below 50 Ω
      G49-3 (P) - G49-7 (GND) Satellite switch set knob not turned to S/S+ position 10 kΩ or higher
      G49-2 (B) - G49-7 (GND) Normal/Custom mode switch pushed and held Below 50 Ω
      G49-2 (B) - G49-7 (GND) Normal/Custom mode switch not pushed 10 kΩ or higher
      G49-6 (ECU) - G49-7 (GND) Satellite switch set knob turned and held at Comf/Eco position Below 50 Ω
      G49-6 (ECU) - G49-7 (GND) Satellite switch set knob not turned to Comf/Eco position 10 kΩ or higher

      If the result is not as specified, replace the satellite switch set.

    2. Apply battery voltage between the terminals of the satellite switch set, and check the illumination condition of the satellite switch set.

      Standard
      Tester Connection Specified Condition

      Battery positive (+) → G49-1 (ILL+)

      Battery negative (-) → G49-8 (ILL-)

      Illuminates

      If the result is not as specified, replace the satellite switch set.

  2. INSPECT SATELLITE SWITCH SET (w/o AVS)


    1. B006E36C06
      *a

      Component without harness connected

      (Satellite Switch Set)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G49-3 (P) - G49-7 (GND) Satellite switch set knob turned and held at Sport position Below 50 Ω
      G49-3 (P) - G49-7 (GND) Satellite switch set knob not turned to Sport position 10 kΩ or higher
      G49-2 (B) - G49-7 (GND) Normal mode switch pushed and held Below 50 Ω
      G49-2 (B) - G49-7 (GND) Normal mode switch not pushed 10 kΩ or higher
      G49-6 (ECU) - G49-7 (GND) Satellite switch set knob turned and held at Eco position Below 50 Ω
      G49-6 (ECU) - G49-7 (GND) Satellite switch set knob not turned to Eco position 10 kΩ or higher

      If the result is not as specified, replace the satellite switch set.

    2. Apply battery voltage between the terminals of the satellite switch set, and check the illumination condition of the satellite switch set.

      Standard
      Tester Connection Specified Condition

      Battery positive (+) → G49-1 (ILL+)

      Battery negative (-) → G49-8 (ILL-)

      Illuminates

      If the result is not as specified, replace the satellite switch set.

  3. INSPECT NO. 2 SATELLITE SWITCH SET


    1. B006E36C07
      *a

      Component without harness connected

      (No. 2 Satellite Switch Set)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G59-3 (SNSW) - G59-7 (E) No. 2 satellite switch set knob turned and held at SNOW position Below 50 Ω
      G59-3 (SNSW) - G59-7 (E) No. 2 satellite switch set knob not turned to SNOW position 10 kΩ or higher

      If the result is not as specified, replace the No. 2 satellite switch set.

    2. Apply battery voltage between the terminals of the No. 2 satellite switch set, and check the illumination condition of the No. 2 satellite switch set.

      Standard
      Tester Connection Specified Condition

      Battery positive (+) → G59-1 (ILL+)

      Battery negative (-) → G59-8 (ILL-)

      Illuminates

      If the result is not as specified, replace the No. 2 satellite switch set.