NAVIGATION SYSTEM, Diagnostic DTC:B15C8

DTC Code DTC Name
B15C8 Digital TV Antenna 1 Disconnected

DESCRIPTION

This DTC is stored when a malfunction occurs in the digital TV antenna which is connected to the radio receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C8 Digital TV Antenna 1 Disconnected Television antenna assembly is not connected.

  • Television antenna assembly

  • No. 3 antenna cord sub-assembly

  • No. 2 antenna cord sub-assembly

  • No. 1 antenna cord sub-assembly

  • Windshield glass (digital TV antenna)

  • Radio receiver assembly

WIRING DIAGRAM

B008H6NE01

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK DTC


    1. Recheck for DTCs and check if the same DTC is output again.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  3. CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. B008HM6C01
      *a

      Front view of wire harness connector

      (to Television Antenna Assembly)
      *b

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)

      Remove the antenna connector from the television antenna assembly.

    2. Remove the antenna connector from the No. 2 antenna cord sub-assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-1 - B-1 Always Below 1 Ω
      A-1a - B-1a Always Below 1 Ω
      A-1 - Body ground Always 10 kΩ or higher
      A-1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  4. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. B008GQEC01
      *a

      Front view of wire harness connector

      (to No. 3 Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to No. 1 Antenna Cord Sub-assembly)

      Remove the antenna connector from the No. 3 antenna cord sub-assembly.

    2. Remove the antenna connector from the No. 1 antenna cord sub-assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B-1 - C-2 Always Below 1 Ω
      B-1a - C-2a Always Below 1 Ω
      B-1 - Body ground Always 10 kΩ or higher
      B-1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  5. CHECK NO. 1 ANTENNA CORD SUB-ASSEMBLY


    1. B008J66C01
      *a

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to Radio Receiver Assembly)

      Remove the antenna connector from the No. 2 antenna cord sub-assembly.

    2. Remove the antenna connector from the radio receiver assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C-2 - TV-1 (DTV) Always Below 1 Ω
      C-2a - TV-1a Always Below 1 Ω
      C-2 - Body ground Always 10 kΩ or higher
      C-2a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 1 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  6. CHECK WINDSHIELD GLASS (DIGITAL TV ANTENNA)


    1. B008IHOC26
      *1 Tester Probe
      *2 Tin Foil
      *3 Antenna Wire

      Check for continuity in the antenna.

      Tech Tips

      Check for continuity at the center of each antenna wire as shown in the illustration.

      Note

      When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger as shown in the illustration.

      OK
      There is continuity in the antenna wire.
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR WINDSHIELD GLASS (DIGITAL TV ANTENNA)

    OK

  7. CHECK TELEVISION ANTENNA ASSEMBLY


    1. Replace the television antenna assembly.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check if the same DTC is output again.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (TELEVISION ANTENNA ASSEMBLY IS DEFECTIVE)

    NG

  8. CHECK WINDSHIELD GLASS (DIGITAL TV ANTENNA)


    1. Replace the windshield glass (digital TV antenna).

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check if the same DTC is output again.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      Result
      Proceed to
      OK
      NG

    OK

    END (WINDSHIELD GLASS [DIGITAL TV ANTENNA] IS DEFECTIVE)

    NG

    REPLACE RADIO RECEIVER ASSEMBLY Click here