SPEED LIMITER SYSTEM Speed Limiter System does not Operate

DTC Code DTC Name
Speed Limiter System does not Operate

DESCRIPTION

When the speed limiter is turned on using the speed limiter switch, the ECM illuminates the speed limiter indicator and activates the speed limiter system. Each function of the speed limiter system can be activated by operating the cruise control switch. When the cruise control system is operating, the speed limiter system will not operate.

WIRING DIAGRAM

B283129E02
B283129E04

PROCEDURE

  1. CHECK CRUISE CONTROL SYSTEM

    1. Turn the ignition switch ON.

    2. Turn the cruise control on using the cruise control switch.

    3. Check the operation of each function by operating the cruise control switch.

      Click here

    OK

    Each function of the cruise control system operates normally.

    Result

    Proceed to

    OK

    NG
    NG

    GO TO CRUISE CONTROL SYSTEM

    Click here

    OK

  2. READ VALUE USING GTS (ASL MAIN SWITCH)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus : Powertrain / Cruise Control / Data List / ASL Main Switch.

    5. In accordance with the display on the tester, read the Data List.

      Powertrain > Cruise Control > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      ASL Main Switch

      Speed limiter switch signal

      ON or OFF

      ON: Speed limiter switch on

      OFF: Speed limiter switch off

      -

      Powertrain > Cruise Control > Data List

      Tester Display

      ASL Main Switch

      OK

      When the switch is operated, the display changes as shown above.

    Result

    Proceed to

    OK

    NG
    NG

    CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)Click here

    OK

  3. CHECK FOR DTC (CRUISE CONTROL SYSTEM)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Check for DTCs.

      Click here

      Powertrain > Cruise Control > Trouble Codes

      Result

      Display (DTC output)

      Proceed to

      DTC P0500 and/or DTC P0503 are output

      A

      DTC P0500 and DTC P0503 are not output (for 1NR-FE)

      B

      DTC P0500 and DTC P0503 are not output (for 1ZR-FAE)

      C

      DTC P0500 and DTC P0503 are not output (for 1AD-FTV)

      D
    A

    GO TO CRUISE CONTROL SYSTEM

    Click hereClick here

    B

    REPLACE ECM

    Click here

    C

    REPLACE ECM

    Click here

    D

    REPLACE ECM

    Click here

  4. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

    1. Disconnect the spiral cable sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E6-2 (ECC) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)

    1. Disconnect the ECM connector.

    2. Disconnect the spiral cable sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Table 1. for 1NR-FE and 1ZR-FAE

      Tester Connection

      Condition

      Specified Condition

      A50-40 (ASLM) - E6-12 (ASL)

      Always

      Below 1 Ω

      A50-40 (ASLM) or E6-12 (ASL) - Body ground

      Always

      10 kΩ or higher
      Table 2. for 1AD-FTV

      Tester Connection

      Condition

      Specified Condition

      A118-24 (ASLM) - E6-12 (ASL)

      Always

      Below 1 Ω

      A118-24 (ASLM) or E6-12 (ASL) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT SPIRAL CABLE SUB-ASSEMBLY

    1. Inspect the spiral cable sub-assembly.

      w/ VSC:Click here

      w/o VSC:Click hereClick here

    Result

    Result

    Proceed to

    OK

    A

    NG (w/ VSC)

    B

    NG (w/o VSC)

    C
    B

    REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Click here

    C

    REPLACE SPIRAL CABLE SUB-ASSEMBLY

    Click here

    A

  7. INSPECT STEERING PAD SWITCH ASSEMBLY

    1. Inspect the steering pad switch assembly.

      Click here

    Result

    Result

    Proceed to

    OK (for 1NR-FE)

    A

    OK (for 1ZR-FAE)

    B

    OK (for 1AD-FTV)

    C

    NG

    D
    A

    REPLACE ECM

    Click here

    B

    REPLACE ECM

    Click here

    C

    REPLACE ECM

    Click here

    D

    REPLACE STEERING PAD SWITCH

    Click here