AIR CONDITIONING SYSTEM, Diagnostic DTC:B1443

DTC Code DTC Name
B1443 Air Outlet Damper Control Servo Motor Circuit

DESCRIPTION

The No. 1 air conditioning radiator damper servo sub-assembly (mode) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal, reverse) based on the signals to move the No. 1 air conditioning radiator damper servo sub-assembly (mode) to any position, which controls the air outlet switching.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1443 Air Outlet Damper Control Servo Motor Circuit Air outlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 air conditioning radiator damper servo sub-assembly (mode)

  • No. 1 air conditioning radiator damper servo sub-assembly (mode)

  • Air conditioning harness assembly

  • Air conditioning amplifier assembly

 Memorized (30 seconds or more) -

Tech Tips

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.

WIRING DIAGRAM

B008GXGE12

CAUTION / NOTICE / HINT

Note


  • When DTC B1441, B1442, B1443 and B1446 are output at same time, there would be malfunctioning on No. 1 air conditioning radiator damper servo sub-assembly.

  • When the battery is disconnected, or servo motor or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

    Click here

Tech Tips

Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTC.

      Click here


      Body Electrical > Air Conditioner > Clear DTCs

    2. Check for DTC.

      Click here


      Body Electrical > Air Conditioner > Trouble Codes
      Result
      Result Proceed to
      DTC B1443 is not output A
      DTC B1443 is output B
      DTC B1443 and B1497 are output C

    A

    USE SIMULATION METHOD TO CHECK Click here

    C

    GO TO DTC B1497 Click here

    B

  2. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Operate the MODE switch.

    5. Enter the following menus: Body Electrical / Air Conditioner / Data List.

    6. Check the value(s) by referring to the table below.


      Body Electrical > Air Conditioner > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Air Outlet Servo Pulse (D) No. 1 air conditioning radiator damper servo sub-assembly (mode) target pulse

      Min.: 128

      Max.: 383

      FACE: 256 (pulse)

      B/L: 267 (pulse)

      FOOT-0: 288 (pulse)

      FOOT-R(F): 297 (pulse)

      FOOT-D: 305 (pulse)

      FOOT/DEF: 320 (pulse)

      DEF: 348 (pulse)

      		 -
      Air Outlet Servo Actu Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (mode) actual pulse

      Min.: 128

      Max.: 383

      FACE: 256 (pulse)

      B/L: 267 (pulse)

      FOOT-0: 288 (pulse)

      FOOT-R(F): 297 (pulse)

      FOOT-D: 305 (pulse)

      FOOT/DEF: 320 (pulse)

      DEF: 348 (pulse)

      		 -

      Body Electrical > Air Conditioner > Data List
      Tester Display
      Air Outlet Servo Pulse (D)
      Air Outlet Servo Actu Pulse(D)
      OK
      When the mode switch is turned, the actual pulse changes following the target pulse.
      Result
      Result Proceed to
      Target pulse and actual pulse do not change A
      Target pulse changes but actual pulse does not change B
      Actual pulse changes following the target pulse (When troubleshooting according to the DTC) C
      Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) D

    A

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    C

    CHECK FOR DTC Click here

    D

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    B

  3. CHECK NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (MODE)


    1. Replace the No. 1 air conditioning radiator damper servo sub-assembly (mode).

      Click here

      Tech Tips

      Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.

    2. Clear the DTC.

      Click here


      Body Electrical > Air Conditioner > Clear DTCs

    3. Check for DTC.

      Click here


      Body Electrical > Air Conditioner > Trouble Codes
      Result
      Result Proceed to
      DTC B1443 is not output A
      DTC B1443 is output B

    A

    END (NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY [MODE] IS DEFECTIVE)

    B

  4. CHECK AIR CONDITIONING HARNESS ASSEMBLY


    1. Replace the air conditioning harness assembly.

      Click here

      Tech Tips

      Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.

    2. Clear the DTC.

      Click here


      Body Electrical > Air Conditioner > Clear DTCs

    3. Check for DTC.

      Click here


      Body Electrical > Air Conditioner > Trouble Codes
      Result
      Result Proceed to
      DTC B1443 is not output A
      DTC B1443 is output B

    A

    END (AIR CONDITIONING HARNESS ASSEMBLY IS DEFECTIVE)

    B

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

  5. CHECK FOR DTC


    1. Clear the DTC.

      Click here


      Body Electrical > Air Conditioner > Clear DTCs

    2. Check for DTC.

      Click here


      Body Electrical > Air Conditioner > Trouble Codes
      Result
      Result Proceed to
      DTC B1443 is not output A
      DTC B1443 is output B

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here