STOP AND START SYSTEM DATA LIST / ACTIVE TEST
DATA LIST
Tip:Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note:In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Data List.
According to the display on the GTS, read the Data List.
ACTIVE TEST
Tip:Using the GTS to perform Active Tests allows relays, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Active Test.
Perform the Active Test by referring to the table below.
Powertrain > Stop and Start > Data List
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
Eco Warning |
Stop and start indicator light status |
ON/OFF |
OFF: Stop and start indicator light off or on (not blinking) under normal system operation |
ON: Any malfunction occurs in the system and the stop and start indicator light is blinking. |
Coolant Temp |
Engine coolant temperature |
Min.: 16°C (60.8°F), Max.: 127°C (260.6°F) |
75 to 95°C (167 to 203°F): Idling after engine warmed up |
This is sent from the ECM. |
Engine Spd (ECM) |
Engine speed signal from ECM via CAN communication |
Min.: 0 rpm, Max.: 12800 rpm |
720 to 820 rpm: Idling after engine warmed up (for 1ND-TV) 600 to 700 rpm: Idling after engine warmed up (for 8NR-FTS with Manual Transaxle) 680 to 780 rpm: Idling after engine warmed up (for 8NR-FTS with CVT) |
This is sent from the ECM. |
Engine Spd (NE Signal) |
Engine speed signal from ECM via direct line |
Min.: 0 rpm, Max.: 25599 rpm |
720 to 820 rpm: Idling after engine warmed up (for 1ND-TV) 600 to 700 rpm: Idling after engine warmed up (for 8NR-FTS with Manual Transaxle) 680 to 780 rpm: Idling after engine warmed up (for 8NR-FTS with CVT) |
The pulse signal sent is from NEO terminal of the ECM. |
Deceleration Sens Offset Val |
Deceleration sensor offset value |
Min.: -1176.008 m/s2, Max.: 1176.007 m/s2 |
-0.903 to 0.903 m/s2: After the deceleration sensor zero point learning completion |
- |
Deceleration Sens Calibration |
Deceleration sensor calibration status |
Incmpl / Running / Compl / Err1 / Err2 / Err3 |
Compl: After the deceleration sensor zero point learning completion |
- |
Gradient of Road Surface |
Degree of road gradient |
Min.: 0 m/s2, Max.: 20.4 m/s2 |
-1.4 to 1.4 m/s2: Vehicle is stopped on level surface |
- |
Battery Voltage |
Battery voltage |
Min.: 0 V, Max.: 20 V |
8 to 14 V: Idling |
- |
Battery Voltage 2 |
VB voltage |
Min.: 0 V, Max.: 65.53 V |
8 to 14 V: Idling |
- |
Battery Fluid Temperature |
Battery fluid temperature |
Min.: -40°C (-40°F), Max.: 100°C (212°F) |
Changes according to actual temperature: Driving after engine warmed up |
- |
Battery Temp (Start) |
Battery temperature at engine start |
Min.: -40°C (-40°F), Max.: 100°C (212°F) |
Same as temperature around battery at engine start (after engine start) |
- |
Oper Permission (AT/CVT) |
Permission of stop and start control by continuously variable transaxle system |
NG/OK |
OK: CVT system normal and CVT fluid temperature 25°C (77°F) or higher |
This is sent from the ECM through CAN communication |
Oper Permission (AT/CVT 2) |
Permission of stop and start control by continuously variable transaxle system |
NG/OK |
OK: Oil pump with motor assembly normal |
This is sent from the ECM through CAN communication
Tip:
The oil pump with motor assembly is built into the continuously variable transaxle assembly. |
Engine Type Information |
Information on the engine type from the ECD or SFI system |
Avail/Not Avi |
Avail: Information of the engine type received from the ECM through CAN communication |
Not Avi is displayed if improper engine type information is received from the ECM via CAN communication. |
Starter Type |
Starter assembly type |
Other than Tandem Starter/Tandem Starter |
Other than Tandem Starter |
- |
D Courtesy Switch Signal |
Driver door courtesy switch signal |
ON/OFF |
ON: Driver side door opened OFF: Driver side door closed |
- |
Hood Courtesy Switch |
Hood courtesy switch signal |
ON/OFF |
ON: Engine hood closed OFF: Engine hood opened |
- |
Neutral Switch |
Neutral start switch assembly signal |
ON/OFF |
ON: Shift lever in neutral OFF: Shift lever not in neutral |
- |
Clutch Upper SW |
Clutch switch assembly signal |
ON/OFF |
ON: Clutch pedal fully released OFF: Clutch pedal depressed |
- |
Clutch Lower SW |
Clutch start switch assembly signal |
ON/OFF |
ON: Clutch pedal fully depressed OFF: Clutch pedal released |
- |
Starter |
Starter status |
ON/OFF |
ON: Cranking OFF: Not cranking |
- |
Pinion Gear |
Starter pinion status |
ON/OFF |
ON: Starter pinion operate OFF: Starter pinion not operated |
- |
Starter Motor |
Starter motor status |
ON/OFF |
ON: Cranking OFF: Not cranking |
- |
TC Terminal |
TC and CG terminals of DLC3 |
ON/OFF |
ON: TC and CG terminals of DLC3 are connected OFF: TC and CG terminals of DLC3 are disconnected |
- |
Cancel Switch |
Eco run cancel switch assembly signal |
ON/OFF |
ON: Eco run cancel switch assembly pressed OFF: Eco run cancel switch assembly not pressed |
- |
IG Switch |
Ignition or starter switch assembly*1 or push start switch assembly*2 signal |
ON/OFF |
ON: Ignition switch ON |
- |
Idle |
Engine idling status |
ON/OFF |
ON: Accelerator pedal fully released OFF: Accelerator pedal depressed |
This is sent from the ECM. |
Engine Start (IG SW) |
Engine start by ignition or starter switch assembly*1 or push start switch assembly*2 operation |
ON/OFF |
ON: Engine start by ignition or starter switch assembly*1 or push start switch assembly*2 operation OFF: Except engine start by ignition or starter switch assembly*1 or push start switch assembly*2 operation |
Indicates starter operation by operation of the ignition or starter switch assembly*1 or push start switch assembly*2 |
Stop Light SW (ECM) |
Stop light switch assembly signal from ECM |
ON/OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
This is sent from the ECM. |
Stop Light SW (ABS/VSC) |
Stop light switch assembly signal from brake system |
ON/OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
This is sent from the skid control ECU (brake actuator assembly). |
Fuel Heater Signal(ECD) |
Combustion type power heater signal |
ON/OFF |
ON: Heater switch assembly on OFF: Heater switch assembly off |
- |
Engine Starter Signal |
Starter signal status |
ON/OFF |
ON: Cranking OFF: Not cranking |
This is sent from the ECM. |
Buzzer |
Buzzer status |
ON/OFF |
ON: Buzzer ON OFF: Buzzer does not sound |
Refer to warning buzzer operation conditions. |
Indicat. Light Eco |
Stop and start indicator light status |
ON/OFF |
ON: Stop and start indicator light on or blinking OFF: Stop and start indicator light off |
- |
Oil Prs Warn Light Prohibit |
Oil pressure warning light status |
Permit/Prohibit |
Prohibit: During engine stop by stop and start control Permit: Not during engine stop by stop and start control |
Engine stop and start ECU informs the combination meter assembly that the oil pressure warning light does not come on during engine stop by stop and start control. |
Brake Press Hold Req |
Brake holding pressure requests during the stop and start control |
ON/OFF |
ON: Shift lever in D, S or B and engine stopped by stop and start control OFF: Shift lever in D, S or B and engine not stopped by stop and start control |
ON is displayed when a brake fluid pressure holding request is sent during stop and start control or the engine is stopped by stop and start control with the shift lever in D, S or B. |
Brake Pressure Hold Request Status |
Brake fluid pressure holding status during stop and start control |
Normal Release / Quick Release / Hold / Immediate Release |
- |
- |
S&S Cancel Light Code |
Transmission code from the engine stop and start ECU to the combination meter assembly |
0: extinction / 1: lighting / 2: blink / 3: - / 4: DTC output |
0: Stop and start cancel indicator light off 1: Stop and start cancel indicator light on |
Stop and start cancel indicator light on/blinking/off request sent to combination meter assembly. |
Starter Operation # |
Number of starter operations (count record) |
Min.: 0, Max.: 1048575 |
- |
- |
Number of Engine Starts (IG-ON) |
The number of starter operations by ignition or starter switch assembly*1 or push start switch assembly*2 operation |
Min.: 0, Max.: 16777215 |
- |
- |
Number of Engine Starts (Stop & Start) |
The number of starter operations by stop and start control |
Min.: 0, Max.: 16777215 |
- |
- |
Number of Engine Starts (Clutch Released) |
The number of starter operations without clutch pedal being depressed |
Min.: 0, Max.: 16777215 |
- |
- |
Number of Engine Starts (Clutch Half-Depressed) |
The number of starter operations with clutch pedal depressed halfway |
Min.: 0, Max.: 16777215 |
- |
- |
Total Number of Engine Starts |
The total number of starter operations |
Min.: 0, Max.: 16777215 |
- |
- |
Vehicle Spd1 (ABS/VSC) |
Vehicle speed signal from skid control ECU via CAN communication |
Min.: 0 km/h (0 mph), Max.: 327.67 km/h (203.6 mph) |
0 km/h (0 mph): Vehicle is stopped |
- |
Steering Angle |
Steering angle |
Min.: -49152 deg, Max.: 49150.5 deg |
- |
- |
Steering Angle Velocity |
Steering wheel turning speed |
Min.: -32768 deg/s, Max.: 32767 deg/s |
- |
- |
Steering Wheel Torque |
Steering wheel torque |
Min.: -327.68 deg/s, Max.: 327.67 Nm |
- |
- |
Battery Current |
Battery current |
Min.: 0 A, Max.: 124.99 A |
- |
- |
Brake Boost Pressure |
Brake booster pressure (absolute pressure) |
Min.: 0 kPa (0 kgf/cm2, 0 psi), Max.: 112 kPa (1.1 kgf/cm2, 16 psi) |
Approx. 100 kPa (1.0 kgf/cm2, 15 psi): Ignition switch ON, brake pedal depressed several times (differs according to atmospheric pressure) |
- |
Brake Negative Pressure |
Brake booster vacuum (negative pressure) |
Min.: 0 kPa (0 kgf/cm2, 0 psi), Max.: 639.98 kPa (6.53 kgf/cm2, 92.8 psi) |
Approx. 0 kPa (0 kgf/cm2, 0 psi): Ignition switch ON, brake pedal depressed several times |
This item cannot be checked if an error occurs in communication with the ECM. |
Ambient Temp Sensor |
Ambient temperature |
Min.: -30°C (-22°F), Max.: 50°C (122°F) |
Close to ambient temperature |
- |
Stop&Start of Eng State |
Stop and start control status |
IG / Run / Stopreq / Stop / Restart |
|
- |
Stop & Start A/C Mode |
Selected air conditioning mode |
Undefined / Normal / S&S Prioritized / A/C Prioritized |
- |
- |
Idling Stop Rate |
Rate of the idling stop time to the entire ignition switch ON time |
Min.: 0%, Max.: 100% |
- |
- |
Total Idling Stop Rate |
Rate of idling stop time to the entire ignition switch ON time |
Min.: 0%, Max.: 100% |
- |
- |
Integrated Current |
Battery integrated current |
Min.: -268434.45 A-sec, Max.: 268435.45 A-sec |
Differs according to the vehicle condition (charge/discharge conditions) |
Refer to "Regarding Battery Integrated Current" below for details.*3 |
Cranking Time |
Engine cranking time (in current trip) (When minimum voltage is detected at engine start) |
Min.: 0 ms, Max.: 134215 ms |
300 to 3000 ms: Duration of starter operation by stop and start control |
- |
Min Voltage(Cranking) |
Minimum battery voltage while engine cranking (in current trip) |
Min.: 0 V, Max.: 327.67 V |
6 to 11 V |
Lowest battery voltage measured in a 5 second period after the starter starts operating. |
Min Volt(After Cranking) |
Minimum battery voltage just after engine cranking |
Min.: 0 V, Max.: 327.67 V |
6 to 11 V |
Minimum battery voltage while the starter operating |
Master Cylinder Pressure |
Brake fluid pressure |
Min.: 0 MPa, Max.: 327.67 MPa |
0 to 5 MPa (when normal pedal effort is applied) |
- |
Status of Battery Charge Control |
Battery charge control status |
Charge Control Coordination Mode/Stop and Start Standalone/Refresh Charge Mode/Stp and Start Restriction Mode/Temperature High/Low Mode/Abnormal Mode/Battery Condition Judgment Mode/Low Temperature Mode |
- |
- |
State of BBC |
Backup boost converter status |
Cycle Err / Overvol / Overload / Normal / Low Vol / Duty Err / S&S Sensor Electric Supply Low / S&S CPU Malfunction / BBC Overcurrent / S&S Starter Overcurrent / S&S Reduced Voltage Reset |
Normal: Backup boost converter operating normally |
|
BBC Check Result |
Backup boost converter check result |
Normal/Abnormal |
Normal: backup boost converter normal |
Abnormal is displayed if excessive electrical load is applied to the converter at engine start. |
Atmosphere Pressure |
Atmospheric pressure (calculated value) |
Min.: 0 kPa (0 kgf/cm2, 0 psi), Max.: 255 kPa (2.6 kgf/cm2, 37 psi) |
Approx. 100 kPa (1.0 kgf/cm2, 15 psi): Ignition switch ON (close to actual atmospheric pressure) |
ECM calculated value |
EPS Load |
Electric power steering current |
Min.: -327.68 A, Max.: 327.67 A |
Approx. 0 A: EPS assist is not activated |
- |
Accelerator Position |
Accelerator pedal position |
Min.: 0%, Max.: 127.5% |
Actual accelerator pedal position |
- |
Shift Position |
Shift lever position |
Unset / B / D / R / N / P |
Shift lever position |
- |
Engine OFF Request |
Engine stop request |
ON/OFF |
ON: Engine stopped due to stop and start control OFF: Not during engine stop by stop and start control |
ON is displayed when fuel-cut is performed by stop and start control, engine start is not requested, or starter is forced to operate. |
Manual Start during S&S |
Manual start during stop and start control operation |
ON/OFF |
- |
- |
Wrong Operation (Start) |
Wrong operation for engine start |
ON/OFF |
OFF |
Unused |
Engine Reverse Rev. |
Engine reverse revolution status |
ON/OFF |
- |
- |
N/Clutch Lower SW Abnoml |
Clutch start switch assembly (for lower) |
ON/OFF |
- |
- |
N/Clutch Upper SW Abnoml |
Clutch switch assembly (for upper) |
ON/OFF |
- |
- |
Permit Idling Stop |
Engine stop standby |
ON/OFF |
- |
- |
Running History |
Vehicle driving record |
ON/OFF |
ON: History of driving vehicle at 2 km/h (1 mph) or more (without DTC output) |
Turns OFF when the engine is stopped by stop and start control. |
4WD Available |
Availability of dynamic torque control AWD system on vehicle |
No / Yes |
- |
Unused |
IPA Available |
Availability of TOYOTA parking assist-sensor system on vehicle |
No / Yes |
No: TOYOTA parking assist-sensor system not equipped Yes: TOYOTA parking assist-sensor system equipped |
- |
Air Suspension Available |
Availability of air suspension system on vehicle |
No / Yes |
- |
Unused |
Welcab Available |
Availability of side left up seat system on vehicle |
No / Yes |
- |
Unused |
External BBC Available |
Availability of eco run vehicle converter assembly (external backup boost converter) on vehicle |
No / Yes |
No: Eco run vehicle converter assembly (external backup boost converter) not equipped Yes: Eco run vehicle converter assembly (external backup boost converter) equipped |
- |
ACC Available |
Availability of dynamic radar cruise control system on vehicle |
No / Yes |
- |
Unused |
Brake Hold Function Available |
Availability of brake hold function on vehicle |
No / Yes |
Yes: Brake hold function available |
- |
Steering Angle Sensor Available |
Availability of steering angle sensor on vehicle |
No / Yes |
Yes: Equipped with steering angle sensor |
- |
Steering Angle Sensor Malfunction |
Steering angle sensor (spiral cable with sensor sub-assembly) malfunction |
ON/OFF |
OFF: Normal |
- |
Steering Angle Sensor Circuit Open (+B) |
Steering angle sensor (spiral cable with sensor sub-assembly) +B circuit malfunction |
ON/OFF |
OFF: Normal |
- |
Steering Angle Sensor Abnormal Value |
Steering angle sensor (spiral cable with sensor sub-assembly) value malfunction |
ON/OFF |
OFF: Normal |
- |
Steering Torque Sensor Malfunction |
Steering torque sensor (electric power steering column sub-assembly) malfunction |
ON/OFF |
OFF: Normal |
- |
EPS Current Enable on Assist |
Power steering assist current value determination |
Avail / Not Avail |
Avail: Power assist current valid |
- |
Auto A/C |
Availability of air conditioning system on vehicle |
Without/With |
With: Equipped with air conditioning system Without: Not equipped without air conditioning system |
Air conditioning information needs to be registered after engine stop and start ECU replacement. |
Cancel Switch (Multi-display) Available |
Existence of the eco run cancel switch assembly |
No/Yes |
- |
- |
Eng Start Req (A/C 2) |
Engine start request from the air conditioning system |
ON/OFF |
ON: Engine start requested to ensure air conditioning system performance OFF: Engine start not requested to ensure air conditioning system performance |
- |
Wheel Speed Malfunction |
Wheel speed sensor malfunction status |
ON/OFF |
OFF: Input value from speed sensor is normal |
ON remains displayed when any input values from the wheel speed sensors are abnormal. |
Slip History |
Slip history existence |
Without / With |
- |
- |
Battery Type |
Set battery type*3 |
Specified / Other |
Specified: Specified battery Other: Non-specified battery |
- |
Communication Method of Brake Boost Sensor |
Method of communication with vacuum sensor |
Not CAN / CAN |
- |
- |
Communication Method of Brake Boost Sensor |
Method of communication with vacuum sensor |
Not CAN / CAN |
- |
- |
O/P Air Bleeding |
Oil pump with motor assembly bleeding status |
Incomplete / Complete |
Complete: Bleeding has been completed |
- |
Oil Pump Relay |
Oil pump motor relay inside ECU status |
ON/OFF |
ON: Oil pump motor relay inside ECU is on |
- |
Oil Pump Status |
Oil pump with motor assembly status |
ON/OFF |
ON: Oil pump with motor assembly operating OFF: Oil pump with motor assembly not operating |
ON is displayed while the engine is stopped by stop and start control
Tip:
The oil pump with motor assembly is built into the continuously variable transaxle assembly. |
Oil Pump Duty |
Requested oil pump with motor assembly duty |
Min.: -32767%, Max.: 32767% |
90%: Oil pump with motor assembly is operating |
Tip:
The oil pump with motor assembly is built into the continuously variable transaxle assembly. |
State of Oil Pump Motor Rotation |
Oil pump with motor assembly rotation status |
Low / High |
Low: Rotating at low speed High: Rotating at high speed |
- |
Oil Pump Motor Rotation Frequency |
Oil pump with motor assembly rotation frequency |
Min.: -32768 Hz, Max.: 32767 Hz |
17 to 200 Hz |
- |
Oper Permission (Shift D position) |
Permission of stop and start control based on the shift lever in D, S or B condition |
NG/OK |
OK: Vehicle being driven with shift lever in D, S or B |
- |
Oper Permission (Neutral Switch) |
Permission of stop and start control based on the neutral position switch conditions |
NG/OK |
OK: Shift lever in neutral |
- |
Oper Permission (Idling) |
Permission of stop and start control based on the engine idle conditions |
NG/OK |
OK: Engine idling (engine speed below 1250 rpm) without accelerator pedal being depressed |
- |
Oper Permission (Vehicle Speed) |
Permission of stop and start control based on the vehicle speed conditions |
NG/OK |
OK: Vehicle is stopped |
OK is displayed while vehicle is stopped. |
Stop&Start Precondition |
Permission of stop and start control with all preconditions met |
ON/OFF |
ON: Preconditions for stop and start control have been met |
Condition of permission or prohibition for terms listed below. (ECM1, ECM2, idling, battery, ABS/VSC2, IGSW, DTC, A/C, interval, after running, engine hood closed, D door closed, cancel switch, steering, interval for starter, key operation, driver side buckle SW, ambient temperature) For details on the preconditions, refer to System Description. |
Stop&Start Precondition 2 |
Permission of stop and start control with all preconditions met |
ON/OFF |
ON: Preconditions for stop and start control have been met |
Condition of permission or prohibition for terms listed below. (Brake negative pressure, starter check complete) |
Oper Permission(Master Cylinder Pressure) |
Permission of stop and start control based on master cylinder pressure |
NG / OK |
OK: Brake pedal depressed while vehicle stopped |
- |
Oper Permission (ECM 1) |
Permission of stop and start control by the ECM |
NG/OK |
OK: Stop and start control is enabled (ECD or SFI system is normal) |
- |
Oper Permission (ECM 2) |
Permission of stop and start control by ECD or SFI system |
NG/OK |
OK: Stop and start control is enabled (ECD or SFI system is normal) |
This is sent from the ECM through CAN communication |
Oper Permission (IG SW) |
Permission of stop and start control based on the ignition or starter switch assembly*1 or push start switch assembly*2 conditions |
NG/OK |
OK: Ignition switch ON for 5 seconds |
- |
Oper Permission (DTC) |
Permission of stop and start control based on the DTC output conditions |
NG/OK |
OK: DTC is not output |
- |
Oper Permission (O/P Check) |
Permission of stop and start control based on oil pump with motor assembly condition |
NG / OK |
OK: Oil pump with motor assembly normal |
Tip:
The oil pump with motor assembly is built into the continuously variable transaxle assembly. |
Oper Permission (Brake Negative Pressure) |
Permission of stop and start control based on the brake booster vacuum conditions |
NG/OK |
OK: Brake booster vacuum approx. 45 kPa (0.5 kgf/cm2, 7 psi) or more (threshold varies by road gradient) |
- |
Oper Permission (Interval) |
Permission of stop and start control based on the engine running time conditions |
NG/OK |
OK: A certain period of time has elapsed after starter operation |
- |
Oper Permission (D Door Closed) |
Permission of stop and start control based on the driver door open/close conditions |
NG/OK |
OK: Driver door closed |
- |
Oper Permission (Engine Hood Closed) |
Permission of stop and start control based on the engine hood open/close conditions |
NG/OK |
OK: Engine hood closed |
- |
Oper Permission (A/C) |
Permission of stop and start control based on the air conditioning conditions |
NG/OK |
OK: Air conditioning conditions are met |
- |
Oper Permission (Ambient Temperature) |
Permission of stop and start control based on the air conditioning conditions |
NG/OK |
OK: Ambient temperature -5°C (23°F) or higher |
- |
Oper Permission (ABS/VSC) |
Permission of stop and start control by vehicle stability control system |
NG / OK |
OK: Stop and start control permitted based on vehicle stability control system normal condition, or Active Test (forced permission) performed |
- |
Oper Permission (No Shift Operation) |
Permission of stop and start control based on shift lever operation condition |
NG / OK |
OK: Shift lever not moved for 1 second or more |
- |
Oper Permission (After Running) |
Permission of stop and start control based on the initial trip conditions after the ignition switch is turned ON |
NG/OK |
OK: Vehicle has been driven at 7 km/h (4 mph) or more |
OK is displayed after the initial trip until the ignition switch is turned off. |
Oper Permission (Neutral SW OFF History) |
Permission of stop and start control based on the shift operation history |
NG/OK |
OK: Neutral position switch OFF record is detected (remains ON until next stop and start system control) |
- |
Oper Permission (Clutch Upper SW OFF History) |
Permission of stop and start control based on the clutch pedal operation history |
NG/OK |
OK: Clutch pedal depressed |
- |
Oper Permission (Battery) |
Permission of stop and start control based on the battery conditions |
NG/OK |
OK: Stop and start control is permitted based on battery conditions, or Active Test (forced permission) is performed |
- |
Oper Permission (Start Min Volt 1) |
Permission of stop and start control based on the battery conditions |
NG/OK |
OK: Battery temperature is 0°C (32°F) or lower and the minimum voltage at starter ON is the threshold value or higher |
If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted |
Oper Permission (Start Min Volt 2) |
Permission of stop and start control based on the battery conditions |
NG/OK |
OK: Battery temperature is 0°C (32°F) or higher and the minimum voltage at starter ON is the threshold value or higher |
If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted |
Oper Permission (Start Min Volt 3) |
Permission of stop and start control based on the battery conditions |
NG/OK |
OK: Battery temperature is 0°C (32°F) or lower and the minimum voltage right after engine cranking is the threshold value or higher |
If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted |
Oper Permission (Start Min Volt 4) |
Permission of stop and start control based on the battery conditions |
NG/OK |
OK: Battery temperature is 0°C (32°F) or higher and the minimum voltage right after engine cranking is the threshold value or higher |
If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted |
Oper Permission (Battery Current) |
Permission of stop and start control based on the battery conditions |
NG/OK |
OK: Battery discharge current is -125 A or less |
Engine stop and start ECU calculated value |
Oper Permission (Integrated Current) |
Permission of stop and start control based on the integrated current value conditions |
NG/OK |
OK: Integrated current value is more than specified |
The status depend on the value of "Integrated Current", and OK/NG threshold differs according to the battery temperature. Refer to "Regarding Battery Integrated Current" below for details.*3 |
Oper Prohibition (Jump Start) |
Prohibition of stop and start control based on the jump start conditions |
Permit/Prohibit |
Prohibit: Engine started by ignition switch operation with the engine hood open |
When Prohibit is displayed, the stop and start control will be prohibited until the ignition switch is turned off. |
Oper Prohibition (Manual Start) |
Prohibition of stop and start control based on the manual start conditions |
Permit/Prohibit |
Prohibit: During manual start |
When Prohibit is displayed, the stop and start control will be prohibited until the ignition switch is turned off. Conditions for Manual Start:
|
Oper Permission (Interval For Starter) |
Permission of stop and start control based on the conditions after engine restart |
NG/OK |
OK: A maximum of 4 minutes have elapsed after engine restarted |
- |
Oper Permission (Cancel Switch) |
Permission of stop and start control based on the eco run cancel switch assembly operation |
NG/OK |
OK: Stop and start control is permitted (the stop and start cancel indicator light is not illuminated) |
- |
Oper Permission (Road Surface Gradient) |
Permission of stop and start control based on the road grade conditions |
NG/OK |
- |
Unused |
Oper Permission (Driver Side Buckle SW) |
Permission of stop and start control based on the driver seat belt condition |
NG/OK |
OK: The driver side buckle switch is fastened |
- |
Oper Permission (Steering) |
Permission of stop and start control by the power steering ECU assembly |
NG/OK |
OK: EPS system is normal operated |
- |
Oper Prohibition (Shift Position Uncertain) |
Prohibition of stop and start control based on shift lever position |
Permit / Prohibit |
Permit: Shift lever position determined |
- |
Oper Permission (Key Operation) |
Permission of stop and start control based on the ignition or starter switch assembly*1 or push start switch assembly*2 operation |
NG/OK |
OK: Ignition or starter switch assembly*1 or push start switch assembly*2 not operated |
- |
Oper Permission (Starter Check Complete) |
Permission of stop and start control based on the starter circuit self-check result |
NG/OK |
OK: Stop and start control enabled (starter circuit normal) |
When the engine stop and start ECU is abnormal, the starter drive circuit is judged to be abnormal, and NG is displayed |
Oper Permission (Brake Master Pressure 0 Point) |
Permission of stop and start control due to completion of brake master cylinder pressure zero point calibration |
NG / OK |
OK: Brake master cylinder pressure zero point calibration completed normally |
- |
Oper Permission (IPA) |
Permission of stop and start control by TOYOTA parking assist-sensor system |
NG / OK |
- |
- |
Oper Prohibition (Engine F/C) |
Prohibition of stop and start control based on the engine fuel-cut prohibition signal |
Permit/Prohibit |
Prohibit: Fuel-cut not performed on ECD or SFI system |
- |
Oper Permission (O/P Air Bleeding) |
Prohibition of stop and start control based on oil pump with motor assembly bleeding condition |
NG / OK |
OK: Bleeding has been completed |
- |
Eng Start Req (Brk Negative Pressure Low) |
Engine start request due to low brake booster vacuum |
ON/OFF |
ON: Brake booster vacuum insufficient while engine stopped by stop and start control |
|
Eng Start Req (IG Switch) |
Engine start request due to ignition or starter switch assembly*1 or push start switch assembly*2 operation |
ON/OFF |
ON: Engine started using ignition or starter switch assembly*1 or push start switch assembly*2 while engine stopped by stop and start control |
- |
Eng Start Req (ABS/VSC) |
Engine start request from vehicle stability control system |
ON/OFF |
ON: Engine start requested by skid control ECU (brake actuator assembly) |
- |
Eng Start Req (ECM) |
Engine start request from ECM |
ON/OFF |
ON: Engine start requested by ECM |
- |
Eng Start Req (A/C) |
Engine start request from Air conditioning system |
ON/OFF |
ON: Engine start requested by air conditioning system |
- |
Eng Start Req (Accelerator) |
Engine start request due to accelerator pedal operation |
ON/OFF |
ON: Engine start requested due to accelerator pedal being depressed |
- |
Eng Start Req (Brake Release) |
Engine start request due to brake pedal operation |
ON/OFF |
ON: Engine start requested due to brake pedal being released |
- |
Eng Start Req (Shift Lever) |
Engine start request due to shift lever operation |
ON/OFF |
ON: Engine start requested due to operation of shift lever |
- |
Eng Start Req (Steering) |
Engine start request by the power steering system |
ON/OFF |
ON: Power steering assist current is abnormal |
- |
Eng Start Req (AT/CVT) |
Engine start request from continuously variable transaxle system |
ON/OFF |
ON: Engine start requested by continuously variable transaxle system |
- |
Eng Start Req (Detect DTC) |
Engine start request due to output of DTCs |
ON/OFF |
ON: Engine start requested due to output of stop and start system DTCs |
- |
Eng Start Req(Shift Uncert) |
Engine start request due to uncertain shift lever position |
ON/OFF |
ON: Engine start requested due to uncertain shift lever position while engine is stopped by stop and start control |
- |
Eng Start Req (Clutch Pedal) |
Engine start request by the clutch pedal |
ON/OFF |
ON: Clutch pedal is depressed |
- |
Eng Start Req (Clutch Lower SW) |
Engine start request by the clutch start switch assembly (for lower) |
ON/OFF |
ON: Clutch pedal is fully depressed |
- |
Eng Start Req (Engine Hood Open) |
Engine start request due to opening of engine hood |
ON/OFF |
ON: Engine hood open (with shift lever in neutral) while the engine is stopped by stop and start control |
- |
Eng Start Req (Battery Condition) |
Engine start request based on battery performance |
ON/OFF |
ON: Engine start requested due to low battery voltage while the engine is stopped by stop and start control |
- |
Eng Start Req (CVT Vehicle Speed) |
Engine start request based on vehicle speed signal from the CVT system |
ON/OFF |
OFF |
Unused |
Eng Start Req (ABS Vehicle Speed) |
Engine start request based on vehicle speed signal from the brake system |
ON/OFF |
ON: Engine start requested due to speed signal while the engine is stopped by stop and start |
Engine start request based on the speed sensor signal |
Eng Start Req(Cancel SW) |
Engine start request by eco run cancel switch assembly |
ON/OFF |
ON: Engine start requested due to eco run cancel switch assembly operation while the engine is stopped by stop and start control |
- |
Eng Start Req (IPA) |
Engine start request from TOYOTA parking assist-sensor system |
ON/OFF |
ON: Engine start requested by TOYOTA parking assist-sensor system |
- |
Eng Start Req(Courtesy SW or Buckle SW) |
Engine start request by courtesy switch (driver side) or driver side buckle switch |
ON/OFF |
ON: Engine start requested due to courtesy switch (for driver side) or driver side buckle switch operation while the engine is stopped by stop and start control |
- |
ABS Running |
Operating condition of the anti-lock brake system |
ON/OFF |
ON: Anti-lock brake system operating |
- |
N Position Switch |
Neutral position switch status |
OK/NG |
OK: System normal |
- |
Alternator Status |
Alternator power generation status |
Normal/Abnormal |
Normal: Alternator operation normal |
- |
EEPROM |
Error in EEPROM |
Normal/Abnormal |
Normal: EEPROM normal |
- |
Dec Sensor Calibration |
Deceleration sensor zero point uncalibrated |
Comp/Incomp |
Comp: Deceleration sensor learning completed |
- |
Deceleration Sensor Movement |
Sticking of the deceleration sensor |
Normal/Abnormal |
Normal: Deceleration sensor not stuck |
- |
Neutral Switch Stuck ON |
Neutral switch stuck on malfunction |
ON/OFF |
OFF: System is normal |
- |
Engine Stall History during S&S (Hood Open) |
History of engine stall caused by depressing the clutch pedal with the engine hood open while the engine is stopped by stop and start control (shift lever in neutral) |
No/Yes |
No: No history |
- |
Engine Stall History during S&S (Collision or Battery Voltage Low) |
History of engine stall due to a collision or low battery voltage when the stop and start control is operating |
No/Yes |
No: No history |
- |
Engine Stall History during Engine Starting (Collision) |
History of engine stall due to a collision while the engine is stopped by stop and start control |
No/Yes |
No: No history |
- |
Engine Start Fail |
History of engine restart failure by stop and start control |
No/Yes |
No: No history |
- |
NE Sensor Circuit Open2 |
Malfunction in the crank position sensor circuit |
ON/OFF |
OFF: System is normal |
ON: No engine speed input at engine start. |
Neutral Switch Stuck OFF |
Neutral switch stuck off malfunction |
ON/OFF |
OFF: System is normal |
- |
Brk Boost Malfunc 1 |
Fail-safe operation due to malfunction in the vacuum sensor assembly |
OK/NG |
OK: System is normal |
Fail-safe operation due to sticking of the vacuum sensor assembly (a change in the sensor value is small when STP signal changes from ON to OFF) |
Brk Boost Malfunc 2 |
Fail-safe operation due to malfunction in the vacuum sensor assembly |
OK/NG |
OK: System is normal |
Fail-safe operation due to sticking of the vacuum sensor assembly (a change in the sensor value is small, even though the vehicle speed has increased from 0 km/h (0 mph) to 30 km/h (18.6 mph) 30 times) |
N Position Voltage Status |
Malfunction in the neutral position switch |
Normal/Hi/Low |
Normal: Neutral position switch voltage normal |
- |
Num of Current Code |
Number of currently stored DTCs |
Min.: 0, Max.: 255 |
- |
- |
Number of Oper Prohibition (ECM 1) |
Number of stop and start control prohibitions when ECM conditions are not met |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (ECM 2) |
Number of stop and start control prohibitions due to ECD or SFI system |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Engine F/C) |
Number of stop and start control prohibitions due to fuel-cut |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Jump Start) |
Number of stop and start control prohibitions due to jump start |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Engine Hood Closed) |
Number of stop and start control prohibitions due to open engine hood |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (AT/CVT 1) |
Number of stop and start control prohibitions due to continuously variable transaxle system condition |
Min.: 0, Max.: 2147483647 |
- |
- |
Number of Oper Prohibition (AT/CVT 2) |
Number of stop and start control prohibitions due to continuously variable transaxle system condition |
Min.: 0, Max.: 2147483647 |
- |
- |
Number of Oper Prohibition (Possible Clutch Lower SW Abnormality) |
Number of stop and start control prohibitions due to clutch start switch assembly (for lower) malfunction |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Possible Clutch Upper SW Abnormality) |
Number of stop and start control prohibitions due to clutch start switch assembly (for upper) malfunction |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Neutral SW OFF History) |
Number of stop and start control prohibitions due to neutral start switch |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Clutch Upper SW OFF History) |
Number of stop and start control prohibitions due to clutch start switch assembly (for upper) |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Battery) |
Number of stop and start control prohibitions due to battery condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Start Min Volt) |
Number of stop and start control prohibitions due to battery condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Battery Current) |
Number of stop and start control prohibitions due to battery condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Integrated Current) |
Number of stop and start control prohibitions due to battery condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (A/C) |
Number of stop and start control prohibitions due to air conditioning condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Ambient Temperature) |
Number of stop and start control prohibitions due to ambient temperature condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (ABS/VSC 1) |
Number of stop and start control prohibitions due to vehicle stability control system condition |
Min.: 0, Max.: 2147483647 |
- |
- |
Number of Oper Prohibition (Brake Negative Pressure) |
Number of stop and start control prohibitions due to brake negative pressure condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Stop&Start Precondition1) |
Number of stop and start control prohibitions due to precondition 1 |
Min.: 0, Max.: 4294967295 |
- |
Condition of permission or prohibition for terms listed below. (ECM1, ECM2, idling, battery, ABS/VSC2, IGSW, DTC, A/C, interval, after running, engine hood closed, D door closed, cancel switch, steering, interval for starter, key operation, driver side buckle SW, ambient temperature) For details on the preconditions, refer to System Description. |
Number of Oper Prohibition (Stop&Start Precondition2) |
Number of stop and start control prohibitions due to precondition 2 |
Min.: 0, Max.: 4294967295 |
- |
Condition of permission or prohibition for terms listed below. (Brake negative pressure, starter check complete) |
Number of Oper Prohibition (DTC) |
Number of stop and start control prohibitions due to DTC output |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Abnormal Wheel Speed Sensor Inputs) |
Number of stop and start control prohibitions due to abnormal vehicle speed signal input |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Deceleration Sensor Abnormal) |
Number of stop and start control prohibitions due to deceleration sensor malfunction |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Interval For Starter) |
Number of stop and start control prohibitions due to starter fail-safe operation |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Interval) |
Number of stop and start control prohibitions due to periodic control prohibition after engine stop |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Cancel Switch) |
Number of stop and start control prohibitions due to eco run cancel switch assembly operation |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (IPA) |
Number of stop and start control prohibitions due to TOYOTA parking assist-sensor system |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Driver Side Buckle SW) |
Number of stop and start control prohibitions due to unfastened driver seat belt |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (D Door Closed) |
Number of stop and start control prohibitions due to open driver door |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (IG SW) |
Number of stop and start control prohibitions due to Ignition or starter switch assembly*1 or push start switch assembly*2 operation |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (After Running) |
Number of stop and start control prohibitions based on the initial trip conditions |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Manual Start) |
Number of stop and start control prohibitions due to manual start condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Manual Start during S&S) |
Number of stop and start control prohibitions due to manual start condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Idling) |
Number of stop and start control prohibitions due to idling condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Road Surface Gradient) |
Number of stop and start control prohibitions due to road surface gradient condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Steering) |
Number of stop and start control prohibitions due to power steering system condition |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (No Shift Operation) |
Number of stop and start control prohibitions based on shift lever position condition |
Min.: 0, Max.: 2147483647 |
- |
- |
Number of Oper Prohibition (Key Operation) |
Number of stop and start control prohibitions due to Ignition or starter switch assembly*1 or push start switch assembly*2 operation |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Starter Check Complete) |
Number of stop and start control prohibitions due to incomplete starter circuit check |
Min.: 0, Max.: 4294967295 |
- |
- |
Number of Oper Prohibition (Brake Master Pressure 0 Pt Calib Incomp) |
Number of stop and start control prohibitions due to oil pump with motor assembly malfunction |
Min.: 0, Max.: 2147483647 |
- |
- |
Number of Oper Prohibition (O/P Check) |
Number of stop and start control prohibitions due to side left up seat system condition |
Min.: 0, Max.: 2147483647 |
- |
Unused |
Number of Eng Start Req (ECM) |
Number of engine start requests from ECD or SFI system |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Engine Hood Open) |
Number of engine start requests due to opening of engine hood while engine is stopped by stop and start control |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (AT/CVT) |
Number of engine start requests from continuously variable transaxle system |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Clutch Lower SW) |
Number of engine start requests from clutch start switch assembly (for lower) |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Battery Condition) |
Number of engine start requests due to low battery performance |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (A/C) |
Number of engine start requests from air conditioning system |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (ABS/VSC) |
Number of engine start requests from vehicle stability control system |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Brk Negative Pressure Low) |
Number of engine start requests due to low brake booster vacuum |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Shift P Position and Brake) |
Indicates the number of the engine start requests due to low brake booster vacuum while the engine is stopped by stop and start control with the shift lever in P |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Detect DTC) |
Number of engine start requests due to DTC output |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (CVT Vehicle Speed) |
Number of engine start requests due to CVT vehicle speed signal input |
Min.: 0, Max.: 65535 |
- |
Unused |
Number of Eng Start Req (ABS Vehicle Speed) |
Number of engine start requests due to anti-lock brake system vehicle speed signal input |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Cancel SW) |
Number of engine start requests due to eco run cancel switch assembly operation |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (IPA) |
Number of engine start requests from TOYOTA parking assist-sensor system |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Courtesy SW or Buckle SW) |
Number of engine start requests due to driver exiting vehicle |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (IG Switch) |
Number of engine start requests due to Ignition or starter switch assembly*1 or push start switch assembly*2 operation |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Accelerator) |
Number of engine start requests due to accelerator pedal operation |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Steering) |
Number of engine start requests due to steering operation |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Shift Uncert) |
Number of engine start requests due to uncertain shift lever position |
Min.: 0, Max.: 65535 |
- |
- |
Number of Eng Start Req (Wrong Shift Lever Operation) |
Number of engine start requests due to wrong shift lever operation |
Min.: 0, Max.: 4294967295 |
- |
- |
*1: w/o Entry and Start System
*2: w/ Entry and Start System
*3: for 8NR-FTS
*3: Regarding Battery Integrated Current
In the stop and start system, the engine stop and start ECU switches the system control mode (stop and start control permitted/prohibited) based on the battery condition (charge/discharge condition) to protect the battery and to ensure stable engine restarting performance.
The battery charge-discharge condition is determined from the integrated current value calculated from the battery current sensor (generator control ECU assembly) signal. The integrated current value is obtained by multiplying the current (Ampere) detected from the battery current sensor (generator control ECU assembly) by the time (seconds), and it is expressed in a unit A-sec.
Example: Integrated current of -3110 A-sec corresponds to a load where current of 10 A flows out from the battery for 311 seconds.
Using the Data List function of the GTS, the integrated current value can be read by checking the Data List item "Integrated Current". The item "Battery Integrated Current" shows the permission status of stop and start control (ON or OFF) and is judged from the "Integrated Current" value.
Negative integrated current represents battery discharge, and positive represents battery charge. In other words, the "Integrated Current" value of the Data List item will decrease from the present value when the battery is discharged, and the value will increase when the battery is charged.
The engine stop and start ECU determines the amount of power available based on the integrated current value, and it prohibits stop and start control if the value is below the threshold, because the battery might not be able to start the engine. The threshold varies according to the battery temperature.
Furthermore, the integrated current value is recorded inside the engine stop and start ECU memory even if the ignition switch is off, and when the ignition switch is next turned to ON, the value is calculated from the value recorded when the ignition switch was turned off.
Integrated Current Condition 1 (for 1ND-TV):
When "Status of Battery Charge Control" is Charge Control Coordination Mode or Low Temperature Mode:
Stop and Start System Operation (for Condition 1)
Phase A (previous trip integrated current storage):
When the ignition switch is turned off, the integrated current value is recorded in the ECU memory. The value is carried over to the next trip.
Phase B (stop and start control permitted):
Stop and start control is permitted to stop the engine until the integrated current reaches less than -4838 A-sec.
Phase C (charging):
When the integrated current has dropped to less than -4838 A-sec, stop and start control is prohibited from stopping the engine until the current reaches -3974 A-sec.
Phase D (stop and start control permitted):
Stop and start control is permitted to stop the engine until the integrated current reaches less than -4838 A-sec.
Integrated Current Condition 1 (for 8NR-FTS):
When "Status of Battery Charge Control" is Charge Control Coordination Mode, Stop and Start Standalone Mode or Low Temperature Mode:
Stop and Start System Operation (for Condition 1)
Phase A (previous trip integrated current storage):
When the ignition switch is turned off, the integrated current value is recorded in the ECU memory. The value is carried over to the next trip.
Phase B (stop and start control permitted):
Stop and start control is permitted to stop the engine until the integrated current reaches less than -4838 A-sec.
Phase C (charging):
When the integrated current has dropped to less than -4838 A-sec, stop and start control is prohibited from stopping the engine until the current reaches -3974 A-sec.
Phase D (stop and start control permitted):
Stop and start control is permitted to stop the engine until the integrated current reaches less than -4838 A-sec.
Integrated Current Condition 2 (for 1ND-TV):
When "Status of Battery Charge Control" is Stop and Start Standalone Mode, Stop and Start Restriction Mode or Temperature High/Low Mode:
Stop and Start System Operation (for Condition 2)
Phase A (previous trip integrated current storage):
When the ignition switch is turned off, the integrated current value is recorded in the ECU memory. The value is carried over to the next trip.
Phase B (stop and start control permitted):
Stop and start control is permitted to stop the engine until the integrated current reaches less than -864 A-sec.
Phase C (charging):
When the integrated current has dropped to less than -864 A-sec, stop and start control is prohibited from stopping the engine until the current reaches 0 A-sec.
Phase D (stop and start control permitted):
Stop and start control is permitted to stop the engine until the integrated current reaches less than -864 A-sec.
Integrated Current Condition 2 (for 8NR-FTS):
When "Status of Battery Charge Control" is Stop and Start Restriction Mode or Temperature High/Low Mode:
Stop and Start System Operation (for Condition 2)
Phase A (previous trip integrated current storage):
When the ignition switch is turned off, the integrated current value is recorded in the ECU memory. The value is carried over to the next trip.
Phase B (stop and start control permitted):
Stop and start control is permitted to stop the engine until the integrated current reaches less than -864 A-sec.
Phase C (charging):
When the integrated current has dropped to less than -864 A-sec, stop and start control is prohibited from stopping the engine until the current reaches 0 A-sec.
Phase D (stop and start control permitted):
Stop and start control is permitted to stop the engine until the integrated current reaches less than -864 A-sec.
The low battery temperature condition is detected when the battery temperature is less than 10°C (50°F). When the battery temperature becomes 11°C (51.8°F) or higher, the low battery temperature condition is cleared.
Performance (internal resistance) of lead-acid batteries used in typical vehicles changes according to the battery temperature. The internal resistance of the battery tends to be higher when the battery temperature is low. Thus, the stop and start system switches the threshold for determining the power charge according to the battery temperature when performing stop and start control.
If the battery is deteriorated, the internal resistance has also increased and the stop and start rate becomes lower. (The total of idling time while the vehicle is stopped increases.)
When troubleshooting, if the malfunction cannot be identified, the battery might be deteriorated.
Even if stop and start control is prohibited due to the condition of any of the systems listed above, performing the Active Tests allows stop and start control to be performed.
Powertrain > Stop and Start > Active Test
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
Buzzer |
Buzzer activation |
ON/OFF |
- |
Starter |
Starter activation |
ON/OFF |
Note:
|
Permit Cond (A/C) |
When stop by stop and start control is prohibited, prohibition of control based on the air conditioning conditions can be disabled/enabled. |
ON/OFF |
- |
Permit Cond (Battery) |
When stop by stop and start control is prohibited, prohibition of control based on the battery conditions can be disabled/enabled. |
ON/OFF |
- |
Permit Cond (Engine) |
When stop by stop and start control is prohibited, prohibition of control based on the ECD or SFI system conditions can be disabled/enabled. |
ON/OFF |
- |
Permit Cond (ABS) |
When engine stop by stop and start control is prohibited, prohibition of control based on the vehicle stability control system condition can be disabled/enabled. |
ON/OFF |
- |
AT Oil Pump (Hi) |
CVT oil pump can be operated/stopped forcibly (high speed operation) |
ON/OFF |
Note:
Prohibited while the engine is running |
AT Oil Pump (Lo) |
CVT oil pump can be operated/stopped forcibly (low speed operation) |
ON/OFF |
Note:
Prohibited while the engine is running |
Precondition (Control) |
Stop and start control can be permitted/prohibited based on precondition 1 |
ON/OFF |
Condition of permission or prohibition for terms listed below. (ECM1, ECM2, battery, ABS/VSC2, IGSW, DTC, A/C, interval, after running, engine hood closed, D door closed, cancel switch, AT/CVT, AT/CVT2, interval for starter, key operation, driver side buckle SW, ambient temperature) |
Precondition2 (Control) |
Stop and start control can be permitted/prohibited based on precondition 2 |
ON/OFF |
Condition of permission or prohibition for terms listed below. (Idling, road surface gradient, no shift operation, brake negative pressure, steering, O/P check, starter check complete) |
Start Cond (Hood Crtsy) |
When engine stop by stop and start control is prohibited, prohibition of control based on the engine hood conditions can be disabled/enabled |
ON/OFF |
- |