SPIRAL CABLE(for Single Type) INSPECTION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSPECT SPIRAL CABLE SUB-ASSEMBLY

   Note:

   • Do not remove the steering sensor from the spiral cable sub-assembly.

   • As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

   1. Visually check for defects with the spiral cable sub-assembly.

      1. The defects are as follows:

         • Scratches

         • Small cracks

         • Dents

         • Chips

         • Cracks or other damage to the connector

         OK

         No defects are found.

         If any of the defects is found, replace the spiral cable sub-assembly with a new one.

   2. Check the spiral cable sub-assembly.

      Note:

      When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

      

      *A	w/ Steering Heater	-	-
      *a	Component without harness connected (spiral cable sub-assembly)	-	-
      	Interlock	-	-

      1. Set the spiral cable sub-assembly to the center position.

         Click here

      2. Measure the resistance between each terminal of the spiral cable sub-assembly according to the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         G9-1 (D+) - z2-2	Always	Below 1 Ω
         G9-2 (D-) - z2-1
         G8-1 (CCS) - z4-3		3 Ω or less
         G8-2 (ECC) - z1-7
         G8-2 (ECC) - z4-4
         G8-3 (EAU) - z1-8
         G8-4 (ASL) - z1-9
         G8-5 (AU2) - z1-10
         G8-6 (AU1) - z1-11
         G8-7 (SDN) - z1-12
         G8-9 (IL+2) - z1-5
         G8-10 (+DP) - z1-2
         G8-11 (-DP) - z1-3
         G8-12 (DIST) - z1-4
         G8-13 (HO) - z1-1
         G8-14 (SUP) - z1-6
         G175-2 (EHT) - Z5-3		Below 0.1 Ω
         G175-4 (BHT) - Z5-4

      3. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         G9-1 (D+) - z2-2	Always	Below 1 Ω
         G9-2 (D-) - z2-1
         G8-1 (CCS) - z4-3		3 Ω or less
         G8-2 (ECC) - z1-7
         G8-2 (ECC) - z4-4
         G8-3 (EAU) - z1-8
         G8-4 (ASL) - z1-9
         G8-5 (AU2) - z1-10
         G8-6 (AU1) - z1-11
         G8-7 (SDN) - z1-12
         G8-9 (IL+2) - z1-5
         G8-10 (+DP) - z1-2
         G8-11 (-DP) - z1-3
         G8-12 (DIST) - z1-4
         G8-13 (HO) - z1-1
         G8-14 (SUP) - z1-6
         G175-2 (EHT) - Z5-3		Below 0.1 Ω
         G175-4 (BHT) - Z5-4

      4. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         G9-1 (D+) - z2-2	Always	Below 1 Ω
         G9-2 (D-) - z2-1
         G8-1 (CCS) - z4-3		3 Ω or less
         G8-2 (ECC) - z1-7
         G8-2 (ECC) - z4-4
         G8-3 (EAU) - z1-8
         G8-4 (ASL) - z1-9
         G8-5 (AU2) - z1-10
         G8-6 (AU1) - z1-11
         G8-7 (SDN) - z1-12
         G8-9 (IL+2) - z1-5
         G8-10 (+DP) - z1-2
         G8-11 (-DP) - z1-3
         G8-12 (DIST) - z1-4
         G8-13 (HO) - z1-1
         G8-14 (SUP) - z1-6
         G175-2 (EHT) - Z5-3		Below 0.1 Ω
         G175-4 (BHT) - Z5-4

         If the result is not as specified, replace the spiral cable sub-assembly.