OUTER MIRROR SWITCH INSPECTION

PROCEDURE

1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Power Retract Mirror)

   1. Check the mirror select switch and mirror surface adjust switch.

      1. 

         *1	Mirror Select Switch
         *2	Mirror Surface Adjust Switch
         *a	Component without harness connected (Outer Mirror Switch Assembly)

         Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for left side)

         Tester Connection	Condition	Specified Condition
         16 (VL) - 22 (B) 19 (M+) - 20 (E)	UP	Below 1 Ω
         	OFF	10 kΩ or higher
         16 (VL) - 20 (E) 19 (M+) - 22 (B)	DOWN	Below 1 Ω
         	OFF	10 kΩ or higher
         17 (HL) - 22 (B) 19 (M+) - 20 (E)	LEFT	Below 1 Ω
         	OFF	10 kΩ or higher
         17 (HL) - 20 (E) 19 (M+) - 22 (B)	RIGHT	Below 1 Ω
         	OFF	10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for right side)

         Tester Connection	Condition	Specified Condition
         15 (VR) - 22 (B) 19 (M+) - 20 (E)	UP	Below 1 Ω
         	OFF	10 kΩ or higher
         15 (VR) - 20 (E) 19 (M+) - 22 (B)	DOWN	Below 1 Ω
         	OFF	10 kΩ or higher
         14 (HR) - 22 (B) 19 (M+) - 20 (E)	LEFT	Below 1 Ω
         	OFF	10 kΩ or higher
         14 (HR) - 20 (E) 19 (M+) - 22 (B)	RIGHT	Below 1 Ω
         	OFF	10 kΩ or higher

         If the result is not as specified, replace the outer mirror switch assembly.

2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Power Retract Mirror)

   1. Check the mirror select switch and mirror surface adjust switch.

      1. 

         *1	Mirror Select Switch
         *2	Mirror Surface Adjust Switch
         *3	Retract Switch
         *a	Component without harness connected (Outer Mirror Switch Assembly)

         Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for left side)

         Tester Connection	Condition	Specified Condition
         16 (VL) - 22 (B) 19 (M+) - 20 (E)	UP	Below 1 Ω
         	OFF	10 kΩ or higher
         16 (VL) - 20 (E) 19 (M+) - 22 (B)	DOWN	Below 1 Ω
         	OFF	10 kΩ or higher
         17 (HL) - 22 (B) 19 (M+) - 20 (E)	LEFT	Below 1 Ω
         	OFF	10 kΩ or higher
         17 (HL) - 20 (E) 19 (M+) - 22 (B)	RIGHT	Below 1 Ω
         	OFF	10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for right side)

         Tester Connection	Condition	Specified Condition
         15 (VR) - 22 (B) 19 (M+) - 20 (E)	UP	Below 1 Ω
         	OFF	10 kΩ or higher
         15 (VR) - 20 (E) 19 (M+) - 22 (B)	DOWN	Below 1 Ω
         	OFF	10 kΩ or higher
         14 (HR) - 22 (B) 19 (M+) - 20 (E)	LEFT	Below 1 Ω
         	OFF	10 kΩ or higher
         14 (HR) - 20 (E) 19 (M+) - 22 (B)	RIGHT	Below 1 Ω
         	OFF	10 kΩ or higher

         If the result is not as specified, replace the outer mirror switch assembly.

   2. Check the retract switch.

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         If the result is not as specified, replace the outer mirror switch assembly.

         Tester Connection	Condition	Specified Condition
         24 (MF) - 20 (E) 23 (MR) - 22 (B)	Pushed in	Below 1 Ω
         24 (MF) - 22 (B) 23 (MR) - 20 (E)	Not pushed in	Below 1 Ω

         If the result is not as specified, replace the outer mirror switch assembly.