BACK DOOR SUPPORT INSTALLATION

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE

  1. INSTALL BACK DOOR STAY BOLT

    1. Clean the bolt hole on the vehicle body with a non-residue solvent.

    2. When reusing the back door stay bolt:

      1. Apply adhesive to the threads of the back door stay bolt.

        Adhesive

        Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    3. Install the back door stay bolt.

      24 N*m

      245 kgf*cm

      18 ft.*lbf

  2. INSTALL INNER ROOF SIDE GARNISH (for 5 Door)

    Click here

  3. INSTALL INNER ROOF SIDE GARNISH (for 3 Door)

    Click hereClick here

  4. INSTALL ROOF SIDE GARNISH END COVER (for 3 Door)

    Click hereClick here

  5. INSTALL INNER ROOF SIDE GARNISH COVER LH (for LH Side)

    w/o Luggage Compartment Room Light:

    Click here

  6. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side)

    w/ Luggage Compartment Room Light:

    Click here

  7. INSTALL REAR SEAT SIDE GARNISH (for 5 Door)

    Click here

  8. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY (for 3 Door)

    Click hereClick here

  9. CONNECT NO. 1 REAR SEAT OUTER BELT ASSEMBLY (for 5 Door)

    Click here

  10. CONNECT NO. 1 REAR SEAT OUTER BELT ASSEMBLY (for 3 Door)

    Click here

  11. CONNECT FRONT SEAT OUTER BELT ASSEMBLY (for 3 Door)

    Click here

  12. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for 5 Door)

    for LH Side:

    Click here

  13. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH (for 5 Door)

    for RH Side:

    Click here

  14. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for 3 Door)

    for LH Side:

    Click hereClick here

  15. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for 3 Door)

    for RH Side:

    Click hereClick here

  16. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for 3 Door)

    for LH Side:

    Click here

  17. INSTALL COWL SIDE TRIM BOARD RH (for 3 Door)

    for RH Side:

    Click here

  18. INSTALL REAR SEAT ASSEMBLY (for Separate Seat Type)

    Click here

  19. INSTALL REAR SEAT ASSEMBLY (for Bench Seat Type)

    Click here

  20. INSTALL REAR FLOOR MAT ASSEMBLY

    Click here

  21. INSTALL BACK DOOR STAY COVER

    1. Engage the clamp to install the back door stay cover.

    2. for LH Side:

      1. Engage the claw to connect the No. 1 back door wire.

  22. INSTALL BACK DOOR STAY ASSEMBLY

    Note:

    • Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing.

    • Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.

    • Do not apply any horizontal load to the back door stay assembly in order to prevent the piston rod from deforming.

    1. B371525

      Install the back door stay assembly on the 2 ball joints.

      Note:

      Install the back door stay assembly while supporting the back door by hand.

    2. Engage the 2 stop rings.

    3. Check that the back door stay assembly is engaged in the ball joint and that the back door stay assembly cannot be pulled out.

  23. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

    Click here