PRE-COLLISION SYSTEM TERMINALS OF ECU


  1. CHECK DRIVING SUPPORT ECU ASSEMBLY

    B005AFKE64

    1. Measure the voltage and resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I159-7 (B) - I159-28 (GND)

      Y - W-B*1

      LG - W-B*2

      		 Power source Engine switch on (IG)

      11 to 14 V*1

      10.5 to 16 V*2
      Engine switch off Below 1 V
      I159-3 (BZ) - I159-28 (GND) SB - W-B Skid control buzzer output Engine switch on (IG), buzzer not sounding 11 to 14 V
      Engine switch on (IG), buzzer sounding Below 1 V
      I159-28 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

      *1: w/o Stop and Start System

      *2: w/ Stop and Start System

    2. Check for pulses according to the value(s) in the table below.

      Tech Tips

      If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the driving support ECU assembly is suspected.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      I159-8 (CA1P) - I159-28 (GND) L - W-B CAN communication signal Engine switch on (IG)

      Pulse generation

      (See waveform 1)
      I159-9 (CA1N) - I159-28 (GND) W - W-B CAN communication signal Engine switch on (IG)

      Pulse generation

      (See waveform 2)
      I159-10 (CA2H) - I159-28 (GND) V - W-B CAN communication signal Engine switch on (IG)

      Pulse generation

      (See waveform 1)
      I159-11 (CA2L) - I159-28 (GND) W - W-B CAN communication signal Engine switch on (IG)

      Pulse generation

      (See waveform 2)

      1. B0058O2E97
        *a 1 V/DIV.
        *b 10 μsec./DIV.

        WAVEFORM 1

        Item Content
        Terminal Name

        Between I159-8 (CA1P) - I159-28 (GND)

        Between I159-10 (CA2H) - I159-28 (GND)
        Tester Range 1 V/DIV., 10 μsec./DIV.
        Condition Engine switch on (IG)

        Tech Tips

        The waveform varies depending on the CAN communication signal.

      2. B005BBTE89
        *a 1 V/DIV.
        *b 10 μsec./DIV.

        WAVEFORM 2

        Item Content
        Terminal Name

        Between I159-9 (CA1N) - I159-28 (GND)

        Between I159-11 (CA2L) - I159-28 (GND)
        Tester Range 1 V/DIV., 10 μsec./DIV.
        Condition Engine switch on (IG)

        Tech Tips

        The waveform varies depending on the CAN communication signal.

  2. CHECK MILLIMETER WAVE RADAR SENSOR

    B0057ZYE48

    1. Measure the voltage and resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      B13-8 (IGB) - B13-1 (SGND) R - W Power source Engine switch on (IG)

      11 to 14 V*1

      10.5 to 16 V*2
      B13-1 (SGND) - Body ground W - Body ground Ground Always Below 1 Ω

      *1: w/o Stop and Start System

      *2: w/ Stop and Start System

    2. Check for pulses according to the value(s) in the table below.

      Tech Tips

      If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the millimeter wave radar sensor is suspected.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      B13-3 (CA2H) - B13-1 (SGND) L - W CAN communication signal Engine switch on (IG)

      Pulse generation

      (See waveform 1)
      B13-2 (CA2L) - B13-1 (SGND) B - W CAN communication signal Engine switch on (IG)

      Pulse generation

      (See waveform 2)
      B13-5 (CA1P) - B13-1 (SGND) SB - W CAN communication signal Engine switch on (IG)

      Pulse generation

      (See waveform 1)
      B13-6 (CA1N) - B13-1 (SGND) W - W CAN communication signal Engine switch on (IG)

      Pulse generation

      (See waveform 2)

      1. B0058O2E97
        *a 1 V/DIV.
        *b 10 μsec./DIV.

        WAVEFORM 1

        Item Content
        Terminal Name

        Between B13-3 (CA2H) and B13-1 (SGND)

        Between B13-5 (CA1P) and B13-1 (SGND)
        Tester Range 1 V/DIV., 10 μsec./DIV.
        Condition Engine switch on (IG)

        Tech Tips

        The waveform varies depending on the CAN communication signal.

      2. B005BBTE89
        *a 1 V/DIV.
        *b 10 μsec./DIV.

        WAVEFORM 2

        Item Content
        Terminal Name

        Between B13-2 (CA2L) and B13-1 (SGND)

        Between B13-6 (CA1N) and B13-1 (SGND)
        Tester Range 1 V/DIV., 10 μsec./DIV.
        Condition Engine switch on (IG)

        Tech Tips

        The waveform varies depending on the CAN communication signal.