FRONT AXLE HUB INSTALLATION


  1. INSTALL FRONT AXLE HUB BEARING


    1. B007T4QE01

      Using SST and a press, install a new front axle hub bearing.

      SST
      09649-17010
      09950-70010   ( 09951-07100 )

      Note

      Do not press on or damage the bearing seal of the front axle hub bearing.

      Tech Tips

      Make sure the lip of the front axle hub bearing faces the vehicle exterior.

  2. INSTALL FRONT DISC


    1. B007TLOE02

      Install the front disc as shown in the illustration.

    2. B007U53E01

      Install the front disc with the 6 bolts.

      Torque:
      62 N*m  { 632 kgf*cm, 46 ft.*lbf }

  3. INSTALL FRONT WHEEL ADJUSTING NUT (w/ ABS)


    1. Install the hub nut to the front axle hub bolt.

    2. Hold the front axle assembly in a vise between aluminium plates.

      Note


      • Do not overtighten the vise.

      • Hold the hub nut in a vise to secure the axle hub and bearing assembly.

    3. B007TVIE01

      Install the skid control rotor as shown in the illustration.

    4. B007TXVE01

      Using SST, install the front wheel adjusting nut.

      SST
      09607-26010
      Torque:
      287 N*m  { 2,930 kgf*cm, 212 ft.*lbf }

      Note

      Do not use an extension bar to avoid applying excess torque to the nut and rotor.

    5. B007QV7

      Using a chisel and hammer, stake the front wheel adjusting nut.

  4. INSTALL FRONT WHEEL ADJUSTING NUT (w/o ABS)


    1. Install the hub nut to the front axle hub bolt.

    2. Hold the front axle assembly in a vise between aluminium plates.

      Note


      • Do not overtighten the vise.

      • Hold the hub nut in a vise to secure the axle hub and bearing assembly.

    3. B007S19

      Install the front wheel bearing dust deflector as shown in the illustration.

    4. B007QMXE02

      Using SST, install the front wheel adjusting nut.

      SST
      09607-26010
      Torque:
      287 N*m  { 2,930 kgf*cm, 212 ft.*lbf }

      Note

      Do not use an extension bar to avoid applying excess torque to the nut and rotor.

    5. B007VZL

      Using a chisel and hammer, stake the front wheel adjusting nut.

  5. INSTALL INNER KNUCKLE GREASE RETAINER CAP (w/ Cap)

  6. INSTALL FRONT LOWER BALL JOINT ASSEMBLY

  7. INSTALL STEERING KNUCKLE

  8. INSTALL OUTER KNUCKLE GREASE RETAINER CAP (w/ Cap)

  9. INSTALL FRONT AXLE ASSEMBLY

  10. INSTALL TIE ROD END SUB-ASSEMBLY

  11. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

  12. INSTALL FRONT SPEED SENSOR (w/ ABS)

  13. INSPECT FRONT AXLE HUB BEARING LOOSENESS


    1. B007U05

      Using a dial indicator, check for runout on the surface of the front axle hub outside the hub bolt.

      Maximum
      0.07 mm (0.0028 in.)

      Note

      Ensure that the dial indicator is set at right angles to the measurement surface.

      If runout exceeds the maximum, replace the front axle hub.

  14. INSPECT FRONT AXLE HUB RUNOUT


    1. B007TQE

      Using a dial indicator, check for looseness near the center of the front axle hub.

      Maximum
      0.05 mm (0.0020 in.)

      Note

      Ensure that the dial indicator is set at right angles to the measurement surface.

      If looseness exceeds the maximum, replace the bearing.

  15. INSTALL FRONT WHEEL

    Torque:
    100 N*m  { 1,020 kgf*cm, 74 ft.*lbf }

  16. INSPECT WHEEL ALIGNMENT

    Click here

  17. CHECK ABS SPEED SENSOR SIGNAL