REAR LOWER ARM INSTALLATION

CAUTION / NOTICE / HINT

Tip:

  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE

  1. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

    1. Temporarily install the rear No. 2 suspension arm assembly to the rear suspension member sub-assembly with the bolt and nut.

      Note:

      • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

      • Insert the bolt with the threaded end facing the front of the vehicle.

  2. INSTALL REAR UPPER COIL SPRING INSULATOR

    Click here

  3. INSTALL REAR LOWER COIL SPRING INSULATOR

    Click here

  4. INSTALL REAR COIL SPRING

    Click here

  5. INSTALL REAR STABILIZER LINK ASSEMBLY

    Click here

  6. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

    Click hereClick here

  7. INSTALL REAR SUSPENSION MEMBER BRACE

    Click here

  8. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

    1. C229546C02
      V100135

      Nut (A)
      V100136

      Nut (B)

      Temporarily install the rear No. 1 suspension arm assembly to the rear axle assembly with a new nut (A).

    2. Using the rear suspension toe adjust cam sub-assembly, rear No. 1 suspension camber adjust cam and nut (B), temporarily install the rear No. 1 suspension arm assembly to the rear suspension member sub-assembly.

      Note:

      • Insert the rear suspension toe adjust cam sub-assembly from the rear of the vehicle.

      • Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.

    3. Fully tighten the nut (A).

      100 N*m

      1020 kgf*cm

      74 ft.*lbf

  9. STABILIZE SUSPENSION

    Click here

  10. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

    1. C212220

      Fully tighten the 2 bolts.

      90 N*m

      918 kgf*cm

      66 ft.*lbf

      Note:

      • Because the nuts have their own stoppers, do not turn the nuts. Tighten the bolts with the nuts secured.

      • Make sure that the rear No. 2 suspension arm assembly remains level when fully tightening the bolt.

  11. INSTALL REAR FLOOR SIDE MEMBER COVER LH (for LH Side)

    Click hereClick hereClick here

  12. INSTALL REAR FLOOR SIDE MEMBER COVER RH (for RH Side)

    Click hereClick hereClick here

  13. INSTALL REAR SUSPENSION ARM COVER

    1. Insert the 2 claws of the rear suspension arm cover into the rear No. 2 suspension arm assembly.

    2. Install the 2 bolts.

      10 N*m

      102 kgf*cm

      7 ft.*lbf

      Note:

      Make sure that the 2 claws of the rear suspension arm cover are inserted.

  14. INSTALL REAR WHEEL

    103 N*m

    1050 kgf*cm

    76 ft.*lbf

  15. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

    1. C271783C01

      *a

      Matchmark

      Align the matchmarks on the rear No. 1 suspension camber adjust cam, rear suspension toe adjust cam sub-assembly and rear suspension member sub-assembly.

    2. Fully tighten the nut.

      100 N*m

      1020 kgf*cm

      74 ft.*lbf

      Note:

      • Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.

      • Make sure that the vehicle is unloaded when fully tightening the nut.

  16. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click hereClick hereClick hereClick here