ECD SYSTEM(for CCo) Injector Circuit

DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

WIRING DIAGRAM

Refer to DTC P062D Click here.

CAUTION / NOTICE / HINT

Note


  • After replacing the ECM, the new ECM needs registration (See page ) and initialization Click here.

  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK EDU (POWER SOURCE)


    1. A004SR5E02
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Injector Driver (EDU))

      Disconnect the injector driver (EDU) connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      B68-2 (+B) - B68-4 (GND) Ignition switch ON 11 to 14 V

    OK

    CHECK FOR INTERMITTENT PROBLEMS Click here

    NG

  2. INSPECT INTEGRATION NO.1 RELAY (EDU RELAY)


    1. Inspect the integration relay (EDU relay) Click here.


    NG

    REPLACE INTEGRATION NO.1 RELAY

    OK

  3. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - EDU)

    A004OSCE01

    1. Remove the integration relay from the engine room No. 1 relay block.

    2. Disconnect the EDU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      B68-2 (+B) - 1B-8 Always Below 1 Ω
      B68-4 (GND) - Body ground Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      B68-2 (+B) or 1B-8 - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Front view of wire harness connector

      (to EDU)
      *2 Engine Room No. 1 Relay Block
      *3

      Front view of wire harness connector

      (to Integration Relay)

    4. Reconnect the EDU connector.

    5. Reinstall the integration relay.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK)


    1. A004QMOE02
      Text in Illustration
      *1 Engine Room No. 1 Relay Block
      *2 EFI MAIN Relay
      *3

      Front view of wire harness connector

      (to Integration Relay)

      Remove the integration relay from the engine room No. 1 relay block.

    2. Remove the EFI MAIN relay from the engine room No. 1 relay block.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      1C-1 - Body ground Always 11 to 14 V

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      3 (EFI MAIN relay holder) - 1B-6 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      3 (EFI MAIN relay holder) or 1B-6 - Body ground Always 10 kΩ or higher

    5. Reinstall the integration relay.

    6. Reinstall the EFI MAIN relay.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM)

    A004NYQE01

    1. Remove the integration relay from the engine room No. 1 relay block.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      A40-44 (IREL) - 1B-7 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      A40-44 (IREL) or 1B-7 - Body ground Always 10 kΩ or higher
      Text in Illustration
      *1

      Front view of wire harness connector

      (to ECM)
      *2 Engine Room No. 1 Relay Block
      *3

      Front view of wire harness connector

      (to Integration Relay)

    4. Reconnect the ECM connector.

    5. Reinstall the integration relay.


    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR