OUTER MIRROR SWITCH INSPECTION

PROCEDURE

  1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Power Retractable Mirror)

    1. Check the mirror select switch and mirror surface adjust switch.

      1. B336514C01

        *a

        Mirror select switch

        *b

        Mirror surface adjust switch

        *c

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)

        Tester Connection

        Condition

        Specified Condition

        15 (VL) - 19 (B)

        17 (M+) - 18 (E)

        UP

        Below 1 Ω

        OFF

        10 kΩ or higher

        15 (VL) - 18 (E)

        17 (M+) - 19 (B)

        DOWN

        Below 1 Ω

        OFF

        10 kΩ or higher

        16 (HL) - 19 (B)

        17 (M+) - 18 (E)

        LEFT

        Below 1 Ω

        OFF

        10 kΩ or higher

        16 (HL) - 18 (E)

        17 (M+) - 19 (B)

        RIGHT

        Below 1 Ω

        OFF

        10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)

        Tester Connection

        Condition

        Specified Condition

        14 (VR) - 19 (B)

        17 (M+) - 18 (E)

        UP

        Below 1 Ω

        OFF

        10 kΩ or higher

        14 (VR) - 18 (E)

        17 (M+) - 19 (B)

        DOWN

        Below 1 Ω

        OFF

        10 kΩ or higher

        13 (HR) - 19 (B)

        17 (M+) - 18 (E)

        LEFT

        Below 1 Ω

        OFF

        10 kΩ or higher

        13 (HR) - 18 (E)

        17 (M+) - 19 (B)

        RIGHT

        Below 1 Ω

        OFF

        10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check the mirror retract switch.

    3. Check the LED illuminates.

      1. B336514C03

        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        Standard

        Measurement Condition

        Specified Condition

        Battery positive (+) → Terminal 12 (ILL+)

        Battery negative (-) → Terminal 22 (ILL-)

        LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.

  2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Power Retractable Mirror)

    1. Check the mirror select switch and mirror surface adjust switch.

      1. B336515C02

        *a

        Mirror select switch

        *b

        Mirror surface adjust switch

        *c

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)

        Tester Connection

        Condition

        Specified Condition

        15 (VL) - 19 (B)

        17 (M+) - 18 (E)

        UP

        Below 1 Ω

        OFF

        10 kΩ or higher

        15 (VL) - 18 (E)

        17 (M+) - 19 (B)

        DOWN

        Below 1 Ω

        OFF

        10 kΩ or higher

        16 (HL) - 19 (B)

        17 (M+) - 18 (E)

        LEFT

        Below 1 Ω

        OFF

        10 kΩ or higher

        16 (HL) - 18 (E)

        17 (M+) - 19 (B)

        RIGHT

        Below 1 Ω

        OFF

        10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)

        Tester Connection

        Condition

        Specified Condition

        14 (VR) - 19 (B)

        17 (M+) - 18 (E)

        UP

        Below 1 Ω

        OFF

        10 kΩ or higher

        14 (VR) - 18 (E)

        17 (M+) - 19 (B)

        DOWN

        Below 1 Ω

        OFF

        10 kΩ or higher

        13 (HR) - 19 (B)

        17 (M+) - 18 (E)

        LEFT

        Below 1 Ω

        OFF

        10 kΩ or higher

        13 (HR) - 18 (E)

        17 (M+) - 19 (B)

        RIGHT

        Below 1 Ω

        OFF

        10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check the mirror retract switch.

      1. B336515C03

        *a

        Mirror retract switch

        *b

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance

        Tester Connection

        Condition

        Specified Condition

        21 (MF) - 18 (E)

        Mirror retract switch retract position

        Below 1 Ω

        20 (MR) - 19 (B)

        Below 1 Ω

        21 (MF) - 19 (B)

        Mirror retract switch return position

        Below 1 Ω

        20 (MR) - 18 (E)

        Below 1 Ω

        If the result is not as specified, replace the outer mirror switch assembly.

    3. Check the LED illuminates (w/o AUTO Power Retractable Mirror).

      1. B336515C01

        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        Standard

        Measurement Condition

        Specified Condition

        Battery positive (+) → Terminal 12 (ILL+)

        Battery negative (-) → Terminal 22 (ILL-)

        LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.

    4. Check the LED illuminates (w/ AUTO Power Retractable Mirror).

      1. B319987C02

        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        Standard

        Measurement Condition

        Specified Condition

        Battery positive (+) → Terminal 3 (ILL+)

        Battery negative (-) → Terminal 23 (ILL-)

        LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.