STARTER(w/ Stop And Start System) REASSEMBLY

CAUTION / NOTICE / HINT

PROCEDURE

1. INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

   
   

   1. 

      *1	Starter Center Bearing Clutch Sub-assembly
      *2	Pinion Drive Lever
      *3	Rubber Seal
      *4	Starter Drive Housing Assembly
      	High-temperature Grease

      Apply high-temperature grease to the pinion drive lever as shown in the illustration.

   2. Install the pinion drive lever and rubber seal to the starter center bearing clutch sub-assembly.

   3. Install the starter center bearing clutch sub-assembly together with the pinion drive lever and rubber seal to the starter drive housing assembly.

   4. 

      High-temperature Grease

      Apply high-temperature grease to the 3 planetary gears, 3 planetary gear shafts and starter center bearing clutch sub-assembly.

   5. Install the 3 planetary gears to the starter center bearing clutch sub-assembly.

2. INSTALL STARTER ARMATURE ASSEMBLY

   
   
   1. 

      *1	Starter Yoke Assembly
      *2	Starter Armature Assembly

      Install the starter armature assembly to the starter yoke assembly.

      Note

      The magnet of the starter yoke assembly may attract the starter armature assembly when the starter armature assembly is installed causing the magnet to break.

3. INSTALL STARTER BRUSH HOLDER ASSEMBLY

   
   

   1. 

      Hold the brush spring back and install the 4 brushes to the starter brush holder assembly.

   2. 

      Install the starter brush holder assembly to the starter armature assembly and push in the 4 brushes.

   3. 

      *a	Grommet
      *b	Negative (-) Brush Holder Plate
      *c	Positive (+) Motor Lead Wire

      Fit the protrusion of the grommet between the negative (-) brush holder plate and positive (+) motor lead wire.

4. INSTALL STARTER YOKE ASSEMBLY

   
   

   1. 

      *1	Starter Commutator End Frame Assembly
      *2	Starter Yoke Assembly
      *a	Lead Wire Rubber
      *b	Cutout

      Install the starter commutator end frame assembly to the starter yoke assembly.

      Note

      Align the lead wire rubber of the starter yoke assembly with the cutout of the starter commutator end frame assembly.

   2. 

      Install the 2 screws.

      Torque:

      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

   3. 

      *1	Starter Yoke Assembly
      *2	Starter Armature Plate
      *a	Stopper
      *b	Protrusion

      Align the starter armature plate so that the protrusion fits between the stoppers of the starter yoke assembly, and install the starter armature plate.

      Note

      Make sure the protrusion of the starter armature plate is inserted between the stoppers of the starter yoke assembly.

   4. 

      *1	Starter Yoke Assembly
      *2	Starter Drive Housing Assembly
      *a	Cutout
      *b	Protrusion

      Install the starter yoke assembly to the starter drive housing assembly.

      Note

      Align the cutout of the starter yoke assembly with the protrusion of the starter drive housing assembly.

   5. 

      Using a T25 "TORX" socket wrench, install the 2 through bolts.

      Torque:

      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

5. INSTALL REPAIR SERVICE STARTER KIT

   
   

   1. 

      *1	Pinion Drive Lever
      *2	Plunger
      *3	Return Spring
      *4	Magnet Switch
      *a	Hook
      *b	Plunger Cover
      *c	Protrusion
      *d	Ventilation Hole

      Hang the hook of the plunger on the pinion drive lever and install the repair service starter kit.

      Tech Tips

      Install the plunger cover so that the ventilation hole is positioned as shown in the illustration.

   2. 

      Install the 2 nuts.

      Torque:

      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

   3. 

      Connect the lead wire with the nut.

      Torque:

      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

6. INSTALL STARTER INRUSH CURRENT REDUCTION RELAY

   
   

   1. 

      Install the starter inrush current reduction relay to the starter drive housing assembly with the 2 bolts.

      Torque:

      7.9 N*m  { 81 kgf*cm, 70 in.*lbf }

   2. 

      Install the wire harness to the starter assembly with the 2 nuts.

      Torque:

      6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

   3. 

      Connect the 2 harness covers.