TRANSMISSION CONTROL CABLE REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point

  • Lane departure alert system (w/ Steering Control)

  • Simple intelligent parking assist system*1

  • Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1

  • Pre-collision system

Click here

Initialize back door lock Power door lock control system

Click here

Gas leaks from exhaust system Inspection After Repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here


CAUTION:


  • B008KL2

    When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

  • Touching high-temperature areas such as the engine and exhaust pipe could result in burns.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. SECURE VEHICLE


    1. Fully apply the parking brake and chock a wheel.

      CAUTION:


      • B008MC4

        Make sure to apply the parking brake and chock a wheel before performing this procedure.

      • If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE BATTERY

    Click here

  5. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

    Click here

  6. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  7. REMOVE NO. 1 ENGINE UNDER COVER

    Click here

  8. REMOVE REAR ENGINE UNDER COVER LH

    Click here

  9. REMOVE NO. 2 CYLINDER HEAD COVER

    Click here

  10. REMOVE RADIATOR COVER

    Click here

  11. REMOVE NO. 1 AIR CLEANER INLET

    Click here

  12. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

    Click here

  13. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  14. REMOVE ECM

    Click here

  15. REMOVE BATTERY CLAMP SUB-ASSEMBLY

    Click here

  16. REMOVE FRONT FLOOR CENTER BRACE

    Click here

  17. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)

    Click here

  18. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR


    1. B008LD4

      Remove 3 nuts and front No. 1 floor heat insulator from the vehicle body.

  19. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY


    1. Move the shift lever to N.

    2. B008MB9C01
      B008LJK Remove in this Direction

      Disconnect the end of the transmission control cable assembly from the floor shift shift lever assembly.

    3. B008KMYC01
      *1 Slider
      B008MD9 Push
      B008LJK Remove in this Direction

      Push in the slider and remove the transmission control cable from the floor shift shift lever assembly as shown in the illustration.

    4. B008LL1

      Remove the nut to disconnect the transmission control cable assembly from the control shaft lever.

    5. Remove the clip to disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.

    6. B008LOU

      Remove the nut to disconnect the transmission control cable assembly from the transmission control cable support.

    7. B008KW6

      Remove the nut.

    8. Disengage the guide to disconnect the transmission control cable assembly from the vehicle body.

    9. B008KYS

      Remove the 2 nuts and transmission control cable assembly from the vehicle body.