HYBRID CONTROL SYSTEM Indicator Circuit

DESCRIPTION

In accordance with the shift lever position, each shift position indicator light will turn on.

WIRING DIAGRAM

PROCEDURE

1. CHECK SHIFT POSITION INDICATOR

   
   

   1. Turn the power switch on (ACC).

   2. Check that each shift position indicator light turns on correctly.

      Result
      Result Proceed to All shift position indicator lights turn on simultaneously A Shift position indicator lights other than corresponding one turn on A Corresponding shift position indicator light does not turn on B No shift position indicator lights turn on B

   3. Turn the power switch off.

   
   

   B

   CHECK HARNESS AND CONNECTOR (SHIFT POSITION SENSOR POWER SOURCE CIRCUIT) Click here

   A

2. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GND)

   
   

   1. Disconnect the O141 and O142 hybrid vehicle control ECU assembly connectors.

   2. 

      *a	Rear view of wire harness connector (to Hybrid Vehicle Control ECU Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition O142-13 (INDP) - Body ground and other terminals Always 10 kΩ or higher O141-8 (INDR) - Body ground and other terminals Always 10 kΩ or higher O142-12 (INDN) - Body ground and other terminals Always 10 kΩ or higher O142-11 (INDD) - Body ground and other terminals Always 10 kΩ or higher O142-10 (INDM) - Body ground and other terminals Always 10 kΩ or higher

   3. Reconnect the O141 and O142 hybrid vehicle control ECU assembly connectors.

      Result
      Proceed to OK NG

   
   

   OK

   REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY Click here

   NG

3. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - SHIFT POSITION INDICATOR)

   
   

   1. Disconnect the O141 and O142 hybrid vehicle control ECU assembly connectors.

   2. Disconnect the O84 shift position indicator connector.

   3. 

      *a	Rear view of wire harness connector (to Hybrid Vehicle Control ECU Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition O142-13 (INDP) - Body ground and other terminals Power switch off 10 kΩ or higher O141-8 (INDR) - Body ground and other terminals Power switch off 10 kΩ or higher O142-12 (INDN) - Body ground and other terminals Power switch off 10 kΩ or higher O142-11 (INDD) - Body ground and other terminals Power switch off 10 kΩ or higher O142-10 (INDM) - Body ground and other terminals Power switch off 10 kΩ or higher

   4. Reconnect the O84 shift position indicator connector.

   5. Reconnect the O141 and O142 hybrid vehicle control ECU assembly connectors.

      Result
      Proceed to OK NG

   
   

   OK

   REPLACE SHIFT POSITION INDICATOR Click here

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

4. CHECK HARNESS AND CONNECTOR (SHIFT POSITION SENSOR POWER SOURCE CIRCUIT)

   
   

   1. Disconnect the O84 shift position indicator connector.

   2. Turn the power switch on (ACC).

   3. 

      *a	Front view of wire harness connector (to Shift Position Indicator)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition O84-6 (PWR) - Body ground Power switch on (ACC) 11 to 14 V

   4. Turn the power switch off.

   5. Reconnect the O84 shift position indicator connector.

      Result
      Proceed to OK NG

   
   

   NG

   REPAIR OR REPLACE POWER SOURCE CIRCUIT

   OK

5. CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL ACCI)

   
   

   1. Turn the power switch on (ACC).

   2. 

      *a	Component with harness connected (Hybrid Vehicle Control ECU Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition A80-22 (ACCI) - Body ground Power switch on (ACC) 11 to 14 V

   3. Turn the power switch off.

      Result
      Proceed to OK NG

   
   

   NG

   REPAIR OR REPLACE POWER SOURCE CIRCUIT

   OK

6. CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN)

   
   

   1. Disconnect the O141 and O142 hybrid vehicle control ECU assembly connectors.

   2. Turn the power switch on (ACC).

   3. 

      *a	Rear view of wire harness connector (to Hybrid Vehicle Control ECU Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition O142-13 (INDP) - Body ground Power switch on (ACC) 11 to 14 V O141-8 (INDR) - Body ground Power switch on (ACC) 11 to 14 V O142-12 (INDN) - Body ground Power switch on (ACC) 11 to 14 V O142-11 (INDD) - Body ground Power switch on (ACC) 11 to 14 V O142-10 (INDM) - Body ground Power switch on (ACC) 11 to 14 V

   4. Turn the power switch off.

   5. Reconnect the O141 and O142 hybrid vehicle control ECU Assembly connectors.

      Result
      Proceed to OK NG

   
   

   OK

   REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY Click here

   NG

7. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - SHIFT POSITION INDICATOR)

   
   

   1. Disconnect the O141 and O142 hybrid vehicle control ECU assembly connectors.

   2. Disconnect the O84 shift position indicator connector.

   3. 

      *a	Rear view of wire harness connector (to Hybrid Vehicle Control ECU Assembly)
      *b	Front view of wire harness connector (to Shift Position Indicator)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition O142-13 (INDP) - O84-4 (P) Always Below 1 Ω O141-8 (INDR) - O84-3 (R) Always Below 1 Ω O142-12 (INDN) - O84-2 (N) Always Below 1 Ω O142-11 (INDD) - O84-1 (D) Always Below 1 Ω O142-10 (INDM) - O84-5 (S) Always Below 1 Ω

   4. Reconnect the O84 shift position indicator connector.

   5. Reconnect the O141 and O142 hybrid vehicle control ECU assembly connectors.

      Result
      Proceed to OK NG

   
   

   OK

   REPLACE SHIFT POSITION INDICATOR Click here

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR