REAR SPEED SENSOR(for AWD) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips

The rear speed sensor rotor is a component of the rear axle hub and bearing assembly. If the rear speed sensor rotor is malfunctioning, replace the rear axle hub and bearing assembly.

PROCEDURE


  1. INSTALL REAR SPEED SENSOR LH (w/o AVS)


    1. Install the rear speed sensor LH and sensor clamp to the rear axle carrier sub-assembly LH and rear trailing arm assembly LH with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Keep the tip of the rear speed sensor LH and installation hole free of foreign matter.

      • Firmly insert the rear speed sensor body into the rear axle carrier sub-assembly LH before tightening the bolt.

      • After installing the rear speed sensor LH to the rear axle carrier sub-assembly LH, make sure that there is no clearance between the rear speed sensor stay and rear axle carrier sub-assembly LH. Also make sure that no foreign matter is stuck between the parts.

      • Do not twist the rear speed sensor wire harness when installing it.

    2. Install the 2 sensor clamps to the rear upper control arm assembly LH with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Do not twist the rear speed sensor wire harness when installing it.

    3. A01R953

      Install the sensor clamp to the rear suspension member sub-assembly with the nut.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Do not twist the rear speed sensor wire harness when installing it.

    4. Connect the rear speed sensor connector.

  2. INSTALL REAR SPEED SENSOR LH (w/ AVS)


    1. Install the rear speed sensor LH and sensor clamp to the rear axle carrier sub-assembly LH and rear trailing arm assembly LH with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Keep the tip of the rear speed sensor LH and installation hole free of foreign matter.

      • Firmly insert the rear speed sensor body into the rear axle carrier sub-assembly LH before tightening the bolt.

      • After installing the rear speed sensor LH to the rear axle carrier sub-assembly LH, make sure that there is no clearance between the rear speed sensor stay and rear axle carrier sub-assembly LH. Also make sure that no foreign matter is stuck between the parts.

      • Do not twist the rear speed sensor wire harness when installing it.

    2. Install the sensor clamp to the rear upper control arm assembly LH with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Do not twist the rear speed sensor wire harness when installing it.

    3. Connect the rear speed sensor connector.

  3. INSTALL REAR SPEED SENSOR RH (w/o AVS)


    1. Install the rear speed sensor RH and sensor clamp to the rear axle carrier sub-assembly RH and rear trailing arm assembly RH with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Keep the tip of the rear speed sensor RH and installation hole free of foreign matter.

      • Firmly insert the rear speed sensor body into the rear axle carrier sub-assembly RH before tightening the bolt.

      • After installing the rear speed sensor RH to the rear axle carrier sub-assembly RH, make sure that there is no clearance between the rear speed sensor stay and rear axle carrier sub-assembly RH. Also make sure that no foreign matter is stuck between the parts.

      • Do not twist the rear speed sensor wire harness when installing it.

    2. Install the 2 sensor clamps to the rear upper control arm assembly RH with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Do not twist the rear speed sensor wire harness when installing it.

    3. A01RCUJ

      Install the sensor clamp to the rear suspension member sub-assembly with the nut.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Do not twist the rear speed sensor wire harness when installing it.

    4. Connect the rear speed sensor connector.

    5. Engage the clamp to install the wire harness to the sensor clamp.

  4. INSTALL REAR SPEED SENSOR RH (w/ AVS)


    1. Install the rear speed sensor RH and sensor clamp to the rear axle carrier sub-assembly RH and rear trailing arm assembly RH with the 2 bolts.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Keep the tip of the rear speed sensor RH and installation hole free of foreign matter.

      • Firmly insert the rear speed sensor body into the rear axle carrier sub-assembly RH before tightening the bolt.

      • After installing the rear speed sensor RH to the rear axle carrier sub-assembly RH, make sure that there is no clearance between the rear speed sensor stay and rear axle carrier sub-assembly RH. Also make sure that no foreign matter is stuck between the parts.

      • Do not twist the rear speed sensor wire harness when installing it.

    2. Install the sensor clamp to the rear upper control arm assembly RH with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Do not twist the rear speed sensor wire harness when installing it.

    3. Connect the rear speed sensor connector.

  5. INSTALL NO. 2 PARKING BRAKE WIRE ASSEMBLY (for LH Side)


    1. Install the No. 2 parking brake wire assembly to the sensor clamp with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

    2. Install the No. 2 parking brake wire assembly to the rear axle carrier sub-assembly LH with the bolt.

      Torque:
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }

    3. Connect the connector.

  6. INSTALL NO. 1 PARKING BRAKE WIRE ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure for the No. 2 parking brake wire assembly.

  7. INSTALL REAR WHEEL

    Click here

  8. CHECK FOR SPEED SENSOR SIGNAL

    Click here