FRONT SEAT CUSHION HEATER (for Power Seat) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


  1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH

    A01DXLWE01
    Text in Illustration
    *1 Tack Pin
    *2 Separate Type Front Seat Cushion Cover
    *3 Front Seat Cushion Heater Assembly LH

    1. Set the front seat cushion heater on the separate type front seat cushion cover.

    2. Using a tacker, install the front seat cushion heater to the separate type front seat cushion cover with 12 new tack pins as shown in the illustration.

      Note

      Do not substitute other metal parts for tack pins.

  2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A01DVA7E02
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  3. INSTALL FRONT SEAT CUSHION COVER WITH PAD


    1. Attach the hooks to install the front seat cushion cover with pad.

    2. Bend the 2 front seat cushion frame claws downward.

    3. A01E0XQ

      for LHD, w/ Seat Heater System:


      1. Attach the 4 front seat cushion heater assembly LH clamps.

      2. Connect the 2 front seat cushion heater assembly LH connectors.

    4. A01DYSFE02
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, attach the rubber bands of the separate type front seatback cover to the seat cushion spring with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  4. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    A01E0EXE02

    1. Install the front seat inner belt assembly LH with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. Connect the connector and attach the 3 clamps.

  5. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. Pass the wire harness of the front seat inner belt assembly below the claw and into the front seat inner cushion shield RH.

      A01DW91
    2. A01E2MZ

      Attach the claw to temporarily install the front seat inner cushion shield RH.

      Note

      Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.

    3. A01DW0F

      Attach the guide and claw.

      Note

      Make sure that the wire harness of the front seat inner belt assembly is not being pinched inside the front seat inner cushion shield.

    4. Install the screw.

  6. INSTALL FRONT POWER SEAT SWITCH LH


    1. Connect the connector.

    2. Install the front power seat switch RH with the 3 screws.

  7. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. Attach the claw and guide to install the front seat cushion shield RH.

    2. Install the 3 screws.

    3. Install the 2 screws.

  8. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A01DZFP

      Attach the 4 claws to install the slide and vertical power seat switch knob.

  9. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A01E176

      Attach the 2 claws to install the reclining power seat switch knob.

  10. INSTALL FRONT SEAT ASSEMBLY

    Click here

  11. CHECK SRS WARNING LIGHT

    Click here

  12. INSPECT FRONT SEAT ASSEMBLY


    1. Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.