POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) Driver Side Power Window does not Operate with Power Window Master Switch

DTC Code DTC Name
Driver Side Power Window does not Operate with Power Window Master Switch

DESCRIPTION

When the ignition switch is ON, the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is operated by the power window regulator master switch assembly. The front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has motor and ECU functions.

WIRING DIAGRAM

B341195E01

CAUTION / NOTICE / HINT

Note:

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

  • If the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has been replaced with a new one, initialize the power window control system.

    Click here

  • When the ECU determines that the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has a malfunction, DTC B2311 is stored.

PROCEDURE

  1. CHECK FOR DTC

    1. Clear the DTC.

      Click here

      Body Electrical > D-Door Motor > Clear DTCs

    2. Check for DTCs.

      Click here

      Body Electrical > D-Door Motor > Trouble Codes

    Result

    Proceed to

    DTC is not output

    DTC is output
    DTC is output

    GO TO DIAGNOSTIC TROUBLE CODE CHART

    Click here

    DTC is not output

  2. PERFORM ACTIVE TEST USING GTS

    1. Perform the Active Test according to the display on the GTS.

      Click here

      CAUTION:

      Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

      Body Electrical > D-Door Motor > Active Test

      Tester Display

      Measurement Item

      Control Range

      Diagnostic Note

      Power Window

      Driver door power window

      OFF, UP or DOWN

      -
      Tip:

      Up and down movement does not occur if the arrow is not pressed and held.

      Body Electrical > D-Door Motor > Active Test

      Tester Display

      Power Window

      OK

      Driver door power window operates normally.

    Result

    Proceed to

    OK

    NG (for LHD)

    NG (for RHD)
    NG (for LHD)

    CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)Click here

    NG (for RHD)

    CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND)Click here

    OK

  3. READ VALUE USING GTS

    1. Read the Data List according to the display on the GTS.

      Click here

      Body Electrical > D-Door Motor > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      D Door P/W Up SW

      Driver door power window manual up switch signal

      ON or OFF

      ON: Driver door power window manual up switch being operated

      OFF: Driver door power window manual up switch not being operated

      -

      D Door P/W Down SW

      Driver door power window manual down switch signal

      ON or OFF

      ON: Driver door power window manual down switch being operated

      OFF: Driver door power window manual down switch not being operated

      -

      Body Electrical > D-Door Motor > Data List

      Tester Display

      D Door P/W Up SW

      D Door P/W Down SW

      OK

      On the GTS screen, ON or OFF is displayed accordingly.

    Result

    Proceed to

    OK (for LHD)

    OK (for RHD)

    NG
    OK (for LHD)

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    Click here

    OK (for RHD)

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    Click here

    NG

    INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLYClick here

  4. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)

    1. B341203C01

      *a

      Front view of wire harness connector

      (to Front Power Window Regulator Motor Assembly LH)

      Disconnect the front power window regulator motor assembly LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      J3-1 (GND) - Body ground

      Always

      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      J3-2 (B) - Body ground

      Always

      11 to 14 V

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    1. Remove the power window regulator master switch assembly.

      Click here

    2. Inspect the power window regulator master switch assembly.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)

    1. B276330C01

      *A

      for LHD

      *B

      for RHD

      *a

      Front view of wire harness connector

      (to Power Window Regulator Master Switch Assembly)

      Disconnect the power window regulator master switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Table 1. for LHD

      Tester Connection

      Condition

      Specified Condition

      J5-1 (E) - Body ground

      Always

      Below 1 Ω
      Table 2. for RHD

      Tester Connection

      Condition

      Specified Condition

      I5-9 (E) - Body ground

      Always

      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Table 3. for LHD

      Tester Connection

      Switch Condition

      Specified Condition

      J5-6 (B) - Body ground

      Ignition switch ON

      11 to 14 V

      Ignition switch off

      Below 1 V
      Table 4. for RHD

      Tester Connection

      Switch Condition

      Specified Condition

      I5-6 (B) - Body ground

      Ignition switch ON

      11 to 14 V

      Ignition switch off

      Below 1 V

    Result

    Proceed to

    OK (for LHD)

    OK (for RHD)

    NG
    OK (for RHD)

    CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK (for LHD)

  7. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

    1. Disconnect the J5 power window regulator master switch assembly connector.

    2. Disconnect the J3 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      J5-8 (U) - J3-10 (UP)

      Always

      Below 1 Ω

      J5-5 (D) - J3-7 (DOWN)

      Always

      Below 1 Ω

      J5-8 (U) or J3-10 (UP) - Body ground

      Always

      10 kΩ or higher

      J5-5 (D) or J3-7 (DOWN) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND)

    1. B341203C02

      *a

      Front view of wire harness connector

      (to Power Window Regulator Motor Assembly RH)

      Disconnect the front power window regulator motor assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      I3-1 (GND) - Body ground

      Always

      Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      I3-2 (B) - Body ground

      Always

      11 to 14 V

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

    1. Disconnect the I5 power window regulator master switch assembly connector.

    2. Disconnect the I3 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      I5-1 (U) - I3-10 (UP)

      Always

      Below 1 Ω

      I5-5 (D) - I3-7 (DOWN)

      Always

      Below 1 Ω

      I5-1 (U) or I3-10 (UP) - Body ground

      Always

      10 kΩ or higher

      I5-5 (D) or I3-7 (DOWN) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR