Click here

MANUAL TRANSMISSION UNIT COMPONENTS

Click here
*A w/ Intelligent Manual Transmission Switch - - *1 BACK-UP LIGHT SWITCH ASSEMBLY *2 BACK-UP LIGHT SWITCH BRACKET *3 CLUTCH HOUSING *4 CLUTCH RELEASE BEARING ASSEMBLY *5 CLUTCH RELEASE FORK SUB-ASSEMBLY *6 COUNTER GEAR SHAFT NUT *7 FRONT BEARING RETAINER *8 FRONT BEARING SHAFT SNAP RING *9 FRONT TRANSMISSION BEARING RETAINER OIL SEAL *10 INPUT SHAFT SHAFT SNAP RING *11 LOCK BALL PIN *12 MANUAL TRANSMISSION FILLER PLUG *13 NO. 1 OIL RECEIVER PIPE *14 SHAFT DETENT BALL *15 TRANSMISSION REVOLUTION SENSOR *16 DRAIN PLUG SUB-ASSEMBLY *17 GASKET *18 STRAIGHT SCREW PLUG WITH HEAD *19 O-RING *20 RELEASE BEARING HUB CAP *21 RELEASE FORK SUPPORT *22 SHIFT AND SELECT LEVER SPRING *23 SHIFT DETENT BALL COMPRESSION SPRING *24 SHIFT DETENT BALL PLUG *25 NO. 2 WITH HEAD STRAIGHT SCREW PLUG -   N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part MP grease precoated Multemp 8158 grease or equivalent Toyota Genuine Clutch Spline Grease or equivalent ★ Precoated part
Click here Click here

ILLUSTRATION

*1 REAR COUNTER GEAR BEARING OR ROLLER *2 FRONT OUTPUT SHAFT BEARING *3 MANUAL TRANSMISSION CASE COVER *4 MANUAL TRANSMISSION CASE SUB-ASSEMBLY *5 MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT *6 NO. 3 OIL RECEIVER PIPE *7 OUTPUT SHAFT *8 REAR TRANSMISSION CASE *9 REVERSE IDLER GEAR *10 REVERSE IDLER GEAR SHAFT BOLT *11 SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING *12 SHIFT FORK SHAFT BEARING *13 RING PIN *14 STRAIGHT PIN *15 TRANSMISSION CASE PLUG *16 REVERSE IDLER GEAR SHAFT *17 REVERSE IDLER GEAR BEARING *18 NO. 2 OIL RECEIVER PIPE *19 BEARING LOCK PLATE *20 GASKET *21 REAR OUTPUT SHAFT BEARING *22 NO. 4 SYNCHRONIZER RING *23 REAR OUTPUT SHAFT BEARING SHIM *24 OUTPUT SHAFT SPACER *25 INPUT SHAFT BEARING - - N*m (kgf*cm, ft.*lbf): Specified torque * For use with SST ● Non-reusable part ★ Precoated part
Click here

ILLUSTRATION

*1 COUNTER GEAR *2 INPUT SHAFT *3 MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY (FRONT SIDE) *4 SHIFT AND SELECT LEVER SHAFT SUB-ASSEMBLY *5 SHIFT FORK AND SHIFT FORK SHAFT ASSEMBLY *6 SHIFT INTERLOCK PLATE STOPPER *7 TRANSMISSION MAGNET *8 TRANSMISSION INTERMEDIATE PLATE *9 MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY (REAR SIDE) *10 RING PIN N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
Click here

ILLUSTRATION

*1 LOCK BALL PIN *2 NO. 1 GEAR SHIFT FORK SHAFT *3 NO. 2 GEAR SHIFT FORK SHAFT *4 NO. 3 GEAR SHIFT FORK SHAFT *5 NO. 4 GEAR SHIFT FORK SHAFT *6 SHIFT AND SELECT LEVER SHAFT *7 SHIFT AND SELECT CAM *8 SHIFT ARM PIVOT *9 NEEDLE ROLLER BEARING *10 SHIFT INTERLOCK PLATE SUB-ASSEMBLY *11 SHIFT ARM *12 INNER SELECT LEVER *13 STRAIGHT PIN *14 SHIFT ARM PIVOT SNAP RING *15 SELECT RETURN COMPRESSION SPRING *16 NO. 1 GEAR SHIFT FORK *17 NO. 2 GEAR SHIFT FORK *18 NO. 3 GEAR SHIFT FORK *19 NO. 4 GEAR SHIFT FORK *20 NO. 1 GEAR SHIFT HEAD *21 NO. 2 GEAR SHIFT HEAD *22 NO. 4 GEAR SHIFT HEAD *23 E-RING - - N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part ★ Precoated part - -
Click here

ILLUSTRATION

*1 FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY *2 SHIFT LEVER HOUSING *3 CONTROL SHIFT LEVER RETAINER GASKET *4 REAR TRANSMISSION CASE *5 RING PIN *6 SHIFT AND SELECT LEVER SHAFT N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part ★ Precoated part - -
Click here

ILLUSTRATION