REAR COMBINATION LIGHT ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH (w/ Deck)


    1. Attach the connector to install the rear combination light socket and wire sub-assembly LH.

  2. INSTALL REAR COMBINATION LIGHT LENS GASKET LH (for Deck-less)


    1. A01LCJRC01
      *a Notch
      B00692L Rear Combination Light Lens Gasket LH

      Install the rear combination light lens gasket LH to the rear combination light body.

      Note


      • If the rear combination light lens gasket LH has been damaged, replace it with a new one.

      • Position the notch of the rear combination light lens gasket LH at the lower center of the rear combination light body.

  3. INSTALL NO. 1 REAR FOG LIGHT BULB (w/ Rear Fog Light)


    1. A01LETUC02
      *a Protrusion
      B0068HS Cutout

      Align the 2 protrusions on the No. 1 rear fog light bulb with the 2 cutouts of the bulb socket and insert the bulb into the bulb socket.

    2. A01LEIFC01
      B0069FO Push in this Direction
      B0068NX Clockwise

      While pushing the No. 1 rear fog light bulb, turn the bulb clockwise to install the bulb.

    3. A01L917C01
      *a Matchmark
      *b Unlock Position Mark
      *c Lock Position Mark
      B0069FO Clockwise

      Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.

  4. INSTALL BACK UP LIGHT BULB


    1. A01LETUC02
      *a Protrusion
      B0068HS Cutout

      w/ Deck:


      1. Align the 2 protrusions on the back up light bulb with the 2 cutouts of the bulb socket and insert the bulb into the bulb socket.

      2. A01LEIFC01
        B0069FO Push in this Direction
        B0068NX Clockwise

        While pushing the back up light bulb, turn the bulb clockwise to install the bulb.

      3. A01LA55C01
        *a Matchmark
        *b Unlock Position Mark
        *c Lock Position Mark
        B0069FO Clockwise

        Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.

    2. for Deck-less:


      1. A01LFOVC02
        *a Protrusion
        B0068HS Cutout

        Align the 2 protrusions on the back up light bulb with the 2 cutouts of the rear combination light body and insert the bulb to the rear combination light body.

      2. A01LFAPC01
        B0069FO Push in this Direction
        B0068NX Clockwise

        While pushing the back up light bulb, turn the bulb clockwise to install the bulb.

  5. INSTALL REAR TURN SIGNAL LIGHT BULB


    1. A01LETUC02
      *a Protrusion
      B0068HS Cutout

      w/ Deck:


      1. Align the 2 protrusions on the rear turn signal light bulb with the 2 cutouts of the bulb socket and insert the bulb into the bulb socket.

      2. A01LE1RC01
        B0069FO Push in this Direction
        B0068NX Clockwise

        While pushing the rear turn signal light bulb, turn the bulb clockwise to install the bulb.

      3. A01LB2BC01
        *a Matchmark
        *b Unlock Position Mark
        *c Lock Position Mark
        B0069FO Clockwise

        Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.

    2. for Deck-less:


      1. A01LFOVC02
        *a Protrusion
        B0068HS Cutout

        Align the 2 protrusions on the rear turn signal light bulb with the 2 cutouts of the rear combination light body and insert the bulb to the rear combination light body.

      2. A01LCVQC01
        B0069FO Push in this Direction
        B0068NX Clockwise

        While pushing the rear turn signal light bulb, turn the bulb clockwise to install the bulb.

  6. INSTALL TAIL AND STOP LIGHT BULB


    1. A01L9P5C02
      *a Upper Protrusion
      *b Lower Protrusion
      B006964 Long Cutout
      B0069AV Short Cutout

      w/ Deck:


      1. Align the upper protrusion of the tail and stop light bulb with the short cutout of the bulb socket and the lower protrusion with the long cutout, and then insert the bulb.

      2. A01LCLHC01
        B0069FO Push in this Direction
        B0068NX Clockwise

        While pushing the tail and stop light bulb, turn the bulb clockwise to install the bulb.

      3. A01L9VKC01
        *a Matchmark
        *b Unlock Position Mark
        *c Lock Position Mark
        B0069FO Clockwise

        Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.

    2. for Deck-less:


      1. A01LCR3C02
        *a Upper Protrusion
        *b Lower Protrusion
        B006964 Long Cutout
        B0069AV Short Cutout

        Align the upper protrusion of the tail and stop light bulb with the short cutout of the rear combination light body and the lower protrusion with the long cutout, and then insert the bulb to the rear combination light body.

      2. A01LAW8C01
        B0069FO Push in this Direction
        B0068NX Clockwise

        While pushing the tail and stop light bulb, turn the bulb clockwise to install the bulb.

  7. INSTALL REAR COMBINATION LIGHT LENS LH (for Deck-less)


    1. Install the rear combination light lens LH to the rear combination light body.