IMMOBILISER SYSTEM(w/o Entry and Start System), Diagnostic DTC:B2793,B2794,B2797 and B2798

DTC Code DTC Name
B2793 Transponder Chip Malfunction
B2794 Unmatched Encryption Code
B2797 Communication Malfunction No. 1
B2798 Communication Malfunction No. 2

DESCRIPTION

  • DTC B2793 is stored when a malfunction is found in the key during key ID code registration or a key ID code is not registered normally. Replace the key if key ID code registration cannot be performed normally and this DTC is output.

  • DTC B2794 is stored when a key with an incomplete key ID code is inserted into the ignition key cylinder.

  • DTC B2797 is stored when a key with a BCC malfunction is inserted into the ignition key cylinder.

  • DTC B2798 is stored when a key is inserted into the ignition key cylinder but a communication error occurs between the key and transponder key ECU assembly.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

B2793

Transponder Chip Malfunction

A transponder chip malfunction (1 trip detection logic*).

  • Key

  • Transponder key coil

  • Transponder key ECU assembly

  • DTC Output Confirmation Operation:

  • Insert the key into the ignition key cylinder.

B2794

Unmatched Encryption Code

A key with an incomplete key ID code is inserted into the ignition key cylinder (1 trip detection logic*).

  • Key

  • Transponder key coil

  • Transponder key ECU assembly

  • DTC Output Confirmation Operation:

  • Insert the key into the ignition key cylinder.

B2797

Communication Malfunction No. 1

A key with a BCC malfunction is inserted into the ignition key cylinder (1 trip detection logic*).

  • Key

  • Transponder key coil

  • Transponder key ECU assembly

  • DTC Output Confirmation Operation:

  • Insert the key into the ignition key cylinder.

B2798

Communication Malfunction No. 2

Key ID code identification cannot be completed within the specified time (1 trip detection logic*).

  • Key

  • Transponder key coil

  • Transponder key ECU assembly

  • DTC Output Confirmation Operation:

  • Insert the key into the ignition key cylinder.

  • *: Only output while a malfunction is present.

Table 1. Vehicle Condition and Fail-safe Operation when Malfunction Detected

Vehicle Condition when Malfunction Detected

Fail-safe Operation when Malfunction Detected

Engine cannot be started

-
Table 2. Related Data List and Active Test

DTC No.

Data List and Active Test

B2793

-

B2794

-

B2797

-

B2798

-

CAUTION / NOTICE / HINT

Note:

  • If the transponder key ECU assembly or key is replaced, refer to Service Bulletin.

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

PROCEDURE

  1. CLEAR DTC

    1. Clear the DTCs.

      Body Electrical > Immobiliser > Clear DTCs

    Result

    Proceed to

    NEXT
    NEXT

  2. CHECK FOR DTC

    1. Insert and remove each registered key one at a time, and check for DTCs each time.

      Body Electrical > Immobiliser > Trouble Codes

      Tip:

      • Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.

      • If DTC B2793, B2794, B2797, or B2798 are stored, clear the DTCs before checking the next key.

      OK

      DTC B2793, B2974, B2797 and B2798 is not output.

    Result

    Result

    Proceed to

    DTCs are not output

    A

    DTCs are output for all of the keys

    B

    DTCs are output for any of the keys

    C
    A

    USE SIMULATION METHOD TO CHECK

    Click hereClick hereClick hereClick hereClick hereClick hereClick here

    C

    REPLACE KEY THAT DTC IS OUTPUT

    B

  3. CHECK CONNECTION OF CONNECTOR

    1. Check that the connectors are properly connected to the transponder key coil.

    2. Check that the engine starts with the key.

      OK

      Engine starts.

    Result

    Proceed to

    OK

    NG
    OK

    END (CONNECTOR WAS NOT CONNECTED PROPERLY)

    NG

  4. REPLACE TRANSPONDER KEY COIL

    1. Replace the transponder key coil.

      Click here

    2. Check that the engine starts with the key.

      OK

      Engine starts.

    Result

    Proceed to

    OK

    NG
    OK

    END (TRANSPONDER KEY COIL WAS DEFECTIVE)

    NG

    REPLACE TRANSPONDER KEY ECU ASSEMBLY