CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) Combination Meter ECU Communication Stop Mode

DTC Code DTC Name
Combination Meter ECU Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Combination Meter ECU Communication Stop Mode

Either condition is met:

  • Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" are output.

    Click here

  • Combination meter assembly main line or connector

  • Power source circuit of combination meter assembly

  • Combination meter assembly ground circuit

  • Combination meter assembly

WIRING DIAGRAM

C355788E02

CAUTION / NOTICE / HINT

Note:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the ignition switch to ON and wait at least 31 seconds, and then drive the vehicle at a speed of 6 km/h (4 mph) or more for 83 seconds or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click hereClick here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tip:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

  1. CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)

    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the E46 combination meter assembly connector.

    3. C263368C70

      *a

      Front view of wire harness connector

      (to Combination Meter Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E46-32 (CANH) - E46-31 (CANL)

      Cable disconnected from negative (-) battery terminal

      108 to 132 Ω

    Result

    Result

    Result

    OK

    NG
    NG

    REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (COMBINATION METER ASSEMBLY)

    OK

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

    1. C263368C71

      *a

      Front view of wire harness connector

      (to Combination Meter Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E46-21 (ET) - Body ground

      Cable disconnected from negative (-) battery terminal

      Below 1 Ω

    2. Reconnect the cable to the negative (-) battery terminal.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      E46-40 (B) - Body ground

      Always

      11 to 14 V

      E46-39 (IG+) - Body ground

      Ignition switch ON

      11 to 14 V

    Result

    Result

    Proceed to

    OK

    A

    • NG (except IG+ signal circuit)

    • NG (for IG+ signal circuit (w/o Stop and Start System))

    B

    NG (for IG+ signal circuit (w/ Stop and Start System))

    C
    A

    REPLACE COMBINATION METER ASSEMBLY

    Click here

    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

    C

    GO TO STOP AND START SYSTEM (FOR BACKUP BOOST CONVERTER CIRCUIT)

    Click here