ECD SYSTEM(for Swirl Control Valve), Diagnostic DTC:P2270

DTC Code DTC Name
P2270 O2 Sensor Signal Biased / Stuck Lean Bank 1 Sensor 2

DESCRIPTION

Refer to DTC P0030 (Click here).

DTC No.

DTC Detection Condition

Trouble Area

P2270

The oxygen concentration measured by the air fuel ratio sensor (for sensor 2) is excessively higher than the estimated oxygen concentration.

(3 trip detection logic)

  • Open or short in air fuel ratio sensor (for sensor 2) circuit

  • Air fuel ratio sensor (for sensor 2)

  • Exhaust system exhaust gas leak
Table 1. Related Data List

DTC No.

Data List

P2270

  • O2 Sensor Lambda Bank 1 Sensor 1

  • O2 Sensor Lambda Bank 1 Sensor 2

WIRING DIAGRAM

Refer to DTC P0030 (Click here).

CAUTION / NOTICE / HINT

Note:

  • When replacing the ECM, the ECM needs Registration and Initialization (Click here).

  • After replacing the Air Fuel Ratio Sensor, the ECM needs initialization (Click here).

Tip:

  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

  1. Air fuel ratio sensors functional check

    Refer to DTC P013A (Click here).

PROCEDURE

  1. CHECK EXHAUST SYSTEM

    1. Check for exhaust gas leaks in the exhaust system.

      OK

      No leakage.

    REPAIR OR REPLACE EXHAUST SYSTEMClick here

  2. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 2) - ECM)

    1. Disconnect the air fuel ratio sensor (for sensor 2) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      C121-1 (AF2+) - C112-130 (AF2+)

      Always

      Below 1 Ω

      C121-2 (AF2-) - C112-133 (AF2-)

      Always

      Below 1 Ω

      C121-3 (HAF2) - C112-17 (HAF2)

      Always

      Below 1 Ω

      C121-5 (TR2) - C112-131 (TR2)

      Always

      Below 1 Ω

      C121-6 (RE2) - C112-134 (RE2)

      Always

      Below 1 Ω

      C121-1 (AF2+) or C112-130 (AF2+) - Body ground

      Always

      10 kΩ or higher

      C121-2 (AF2-) or C112-133 (AF2-) - Body ground

      Always

      10 kΩ or higher

      C121-3 (HAF2) or C112-17 (HAF2) - Body ground

      Always

      10 kΩ or higher

      C121-5 (TR2) or C112-131 (TR2) - Body ground

      Always

      10 kΩ or higher

      C121-6 (RE2) or C112-134 (RE2) - Body ground

      Always

      10 kΩ or higher

    REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)Click here

    REPAIR OR REPLACE HARNESS OR CONNECTORClick here

  3. REPAIR OR REPLACE EXHAUST SYSTEM

    1. Repair or replace the malfunctioning parts of the exhaust system.

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  4. REPAIR OR REPLACE HARNESS OR CONNECTOR

    1. Repair or replace the harness or connector.

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  5. REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)

    1. Replace the air fuel ratio sensor (for sensor 2) (Click here).

    2. Perform O2 sensor learning value reset (Click here).

  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs (Click here).

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.

    END