АВТОМАТИЧЕСКАЯ ТРАНСМИССИЯ В СБОРЕ СНЯТИЕ


  1. DISCONNECT BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  2. REMOVE NO.1 ENGINE UNDER COVER

  3. REMOVE NO.2 ENGINE UNDER COVER (for Pre-Runner)

  4. REMOVE NO.3 ENGINE UNDER COVER (for Pre-Runner)

  5. REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY (except Pre-Runner)

    A01E028E01

    1. Remove the 4 nuts, 4 bolts and frame crossmember.

  6. DISCONNECT HEATED OXYGEN SENSOR

  7. REMOVE EXHAUST PIPE


    1. Remove the exhaust pipe Click here.

  8. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY


    1. for TMT Made:

      Remove the propeller shaft with center bearing assembly Click here.

    2. for TSAM Made:

      Remove the propeller shaft with center bearing assembly Click here.

  9. DRAIN AUTOMATIC TRANSMISSION FLUID


    1. Remove the drain plug and gasket, and drain ATF.

    2. Install a new gasket and the drain plug.

      Torque:
      28 N*m  { 285 kgf*cm, 21 ft.*lbf }

  10. REMOVE MANIFOLD STAY

    A01DZ6QE01

    1. Remove the 3 bolts and manifold stay.

  11. REMOVE NO. 2 MANIFOLD STAY

    A01DX7WE01

    1. Remove the 3 bolts and manifold stay.

  12. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    1. Отверните 6 гаек, снимите выпускной коллектор и прокладку.

  13. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    1. Отверните 6 гаек, снимите выпускной коллектор и прокладку.

  14. DISCONNECT OIL COOLER TUBE

    A01DZJ6

    1. Using a union nut wrench, disconnect the inlet tube and outlet tube.

    2. A01E0HP

      Remove the 2 bolts and 2 clamps.

  15. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

    A01DX06

    1. Remove the nut and disconnect the control cable.

    2. Remove the clip and disconnect the control cable.

  16. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

    A01DV19

    1. Remove the 2 bolts and control cable bracket from the transmission.

  17. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

    A01DYR4

    1. Support the transmission with a transmission jack.

  18. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

    A01E24YE01

    1. Remove the 4 set bolts of the No. 1 engine mounting insulator rear.

    2. Remove the 4 nuts, 4 bolts and frame crossmember.

  19. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR

    A01E1RJ

    1. Remove the 4 bolts, ground cable and engine mounting insulator.

  20. DISCONNECT CONNECTOR

    A01DW1D

    1. Tilt the transmission downward.

      Note

      Make sure the cooling fan does not contact the fan shroud.

    2. Transmission side:

      Disconnect the connectors.


      1. Disconnect the park/neutral position switch connector.

      2. Disconnect the transmission wire connector.

      3. Disconnect the 3 speed sensor connectors.

  21. DISCONNECT WIRE HARNESS

  22. REMOVE STARTER ASSEMBLY


    1. Remove the starter assembly Click here.

  23. REMOVE FLYWHEEL HOUSING SIDE COVER

    A01E1EWE01

    1. Remove the flywheel housing side cover from the cylinder block.

  24. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

    A01DYVG

    1. Turn the crankshaft to gain access to each bolt.

    2. Hold the crankshaft pulley bolt with a wrench and remove the 6 torque converter clutch mounting bolts.

    3. A01E2YV

      Remove the 9 bolts.

    4. Separate and remove the automatic transmission assembly.

  25. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY