REAR SEAT ASSEMBLY(for Fold Down Seat Type) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

Panoramic view monitor system

Click here

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • B0084SX

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

PROCEDURE


  1. PRECAUTION (w/ Rear Seat Side Airbag)

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)

    for 2AR-FE:

    Click here

    for A25A-FKS:

    Click here

    for 2GR-FKS:

    Click here

    for 6AR-FSE:

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If an airbag deploys for any reason, it may cause a serious injury.

    B0087PP

  3. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY


    1. B0088KUC01
      *a Protective Tape
      B0089GN Insert Screwdriver Here
      B00847Z Remove in this Direction

      Using a screwdriver with its tip wrapped with protective tape, disconnect the rear center seat outer belt assembly as shown in the illustration.

  4. REMOVE REAR SEAT HEADREST ASSEMBLY LH (w/ Removable Headrest)


    1. Remove the rear seat headrest assembly LH.

  5. REMOVE REAR SEAT HEADREST ASSEMBLY RH (w/ Removable Headrest)


    1. Remove the rear seat headrest assembly RH.

  6. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. B0084M3C01
      *a Rear Seat Cushion Frame Hook (Front Side)
      *b Rear Seat Cushion Frame Hook (Rear Side)
      B0089GN Place Hand Here
      B00847Z Remove in this Direction (1)
      B008776 Remove in this Direction (2)

      Lift the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the rear seat cushion lock hooks.

      Note

      Be sure to hold the parts of the rear seat cushion assembly directly next to the rear seat cushion frame hooks when lifting it. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

      Standard Measurement
      Area Measurement
      A 245 mm (9.64 in.)

    2. Disengage the 2 rear seat cushion frame hooks on the rear side of the rear seat cushion assembly as shown in the illustration and remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

    3. w/ Seat Heater System:


      1. Disconnect each connector.

      2. Disengage each clamp.

  7. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. B0084SJC01
      B00847Z Remove in this Direction

      Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  8. REMOVE REAR SEATBACK ASSEMBLY LH


    1. Fold the rear seatback assembly LH forward.

    2. B0089NBC01
      *a Fastener

      Disengage the fastener.

    3. B0084SV

      Remove the 2 bolts.

    4. Disengage the 2 guides and remove the rear seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

    5. w/ Seat Heater System:


      1. Disengage the clamp.

  9. REMOVE REAR SEATBACK ASSEMBLY RH


    1. Fold the rear seatback assembly RH forward.

    2. B0086WBC01
      *a Fastener

      Disengage the fastener.

    3. B0083EV

      Remove the 2 bolts.

    4. Disengage the 2 guides and remove the rear seatback assembly RH.

      Note

      Be careful not to damage the vehicle body.

    5. w/ Seat Heater System:


      1. Disengage the clamp.

  10. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the rear door opening trim weatherstrip LH.

  11. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat outer belt LH from the rear seat shoulder belt guide LH.

    2. w/ Rear Seat Side Airbag:


      1. Disconnect the connector.

        Note

        When disconnecting any airbag connector, take care not to damage the airbag wire harness.


        1. B0087EWC04
          *a White Housing Lock
          *b Yellow CPA
          B00847Z Slide in this Direction

          Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

        2. Push down the white housing lock again and disconnect the connector.

          Note

          Do not push down the part (A) shown in the illustration when disconnecting the connector.

    3. B0089CZ

      Remove the bolt.

    4. Disengage the hook and remove the rear side seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  13. REMOVE REAR SIDE SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.