MULTI-MODE MANUAL TRANSAXLE UNIT COMPONENTS
ILLUSTRATION
*1 |
SHIFT AND SELECT ACTUATOR ASSEMBLY |
*2 |
BREATHER PROTECTOR |
*3 |
CLUTCH RELEASE BLEEDER SUB-ASSEMBLY |
*4 |
RELEASE CYLINDER BLEEDER PLUG |
*5 |
RELEASE CYLINDER BLEEDER PLUG CAP |
*6 |
CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY |
*7 |
CLUTCH RELEASE CYLINDER TO BLEEDER TUBE |
*8 |
TRANSMISSION REVOLUTION SENSOR |
*9 |
BACK-UP LIGHT SWITCH ASSEMBLY |
*10 |
MANUAL TRANSMISSION DRAIN PLUG |
*11 |
MANUAL TRANSMISSION FILLER PLUG |
*12 |
NEUTRAL POSITION SWITCH |
*13 |
NO. 1 CLUTCH HOUSING COVER |
*14 |
CLUTCH TUBE BOOT |
*15 |
RING PIN |
*16 |
BREATHER PLUG |
*17 |
O-RING |
*18 |
GASKET |
*19 |
BREATHER PLUG CAP |
*20 |
WIRE HARNESS BRACKET |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
 |
Clutch spline grease |
- |
- |
ILLUSTRATION
*1 |
SHIFT DETENT BALL PLUG |
*2 |
SHIFT DETENT BALL COMPRESSION SPRING |
*3 |
SHIFT DETENT BALL |
*4 |
TRANSMISSION CASE PLUG |
*5 |
TRANSMISSION CASE GASKET |
*6 |
REVERSE IDLER GEAR SHAFT BOLT |
*7 |
STRAIGHT PIN |
*8 |
GASKET |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
★ |
Precoated part |
- |
- |
ILLUSTRATION
*1 |
SHIFT AND SELECT LEVER SHAFT ASSEMBLY |
*2 |
SHIFT INTER LOCK PLATE |
*3 |
DIFFERENTIAL CASE ASSEMBLY |
*4 |
FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
*5 |
FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
*6 |
REVERSE SHIFT ARM BRACKET ASSEMBLY |
*7 |
REVERSE SHIFT FORK SHAFT ASSEMBLY |
*8 |
REVERSE IDLER GEAR SUB-ASSEMBLY |
*9 |
REVERSE IDLER THRUST WASHER |
*10 |
REVERSE IDLER GEAR SHAFT |
*11 |
NO. 1 GEAR SHIFT FORK SHAFT ASSEMBLY |
*12 |
OUTPUT SHAFT ASSEMBLY |
*13 |
NO. 2 GEAR SHIFT FORK SHAFT ASSEMBLY |
*14 |
NO. 3 GEAR SHIFT FORK SHAFT ASSEMBLY |
*15 |
INPUT SHAFT ASSEMBLY |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*1 |
SHIFT AND SELECT LEVER SHAFT |
*2 |
INNER NO. 1 SHIFT LEVER |
*3 |
SHIFT AND SELECT LEVER SHAFT HEAD |
*4 |
INNER SELECT LEVER |
*5 |
FRONT INNER SHIFT LEVER |
*6 |
INNER NO. 2 SHIFT LEVER |
*7 |
SLOTTED SPRING PIN |
- |
- |
ILLUSTRATION
*1 |
TRANSMISSION OIL SEPARATOR |
*2 |
TRANSAXLE CASE OIL SEAL (for RH SIDE) |
*3 |
FRONT TRANSAXLE CASE OIL SEAL |
*4 |
TRANSMISSION MAGNET |
*5 |
FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE) |
*6 |
FRONT DIFFERENTIAL CASE FRONT PLATE WASHER |
*7 |
OUTPUT SHAFT COVER |
*8 |
FRONT OUTPUT SHAFT BEARING (OUTER RACE) |
*9 |
FRONT TRANSAXLE CASE |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
- |
- |
ILLUSTRATION
*1 |
MANUAL TRANSMISSION CASE |
*2 |
TRANSMISSION OIL SEPARATOR |
*3 |
NO. 1 OIL RECEIVER PIPE |
*4 |
FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE) |
*5 |
FRONT DIFFERENTIAL CASE REAR PLATE WASHER |
*6 |
REAR INPUT SHAFT BEARING SHIM |
*7 |
INPUT SHAFT COVER |
*8 |
REAR OUTPUT SHAFT BEARING (OUTER RACE) |
*9 |
REAR OUTPUT SHAFT BEARING SHIM |
*10 |
TRANSMISSION CASE OIL SEAL (for LH SIDE) |
*11 |
MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
- |
- |